https://youtu.be/1Ho59VBAdZc
15-5-2024
all SF full auto disconnect parts have been updated. there was a error in the frame that made it wobble effecting the FA sear. both parts need to be replaced
the BIG 2024 project update status: complete
the parts list can be found here
https://drive.google.com/drive/folders/1XBZvTm_s3VLk_iqTnINIyMt30BXmXn8h
https://youtu.be/E06SEV4Z0yI
added a AR-15 trigger spring compatible SF trigger option
trigger and semi disconnect is updated to prevent binary fire
the Full auto sear part is updated, this can be placed in the frame original FA sear frame
all Bolts have been updated and more nozzle models have been added
A BIG 2024 project update is a view weeks away!!!
so my recommendation is to put your build on hold.
Barrel / UNW hop up unit will be updated
Bolts will be updated
bolt front caps
internal pars will be updated
and the manual
why? Better FPS/joule out putt
a more easy and relabel build
better nozzle support
nozzle spring guide (is all ready a beta thing)
For beta user keep in mind that I’m working and testing parts that are newer then the beta parts.
When this update is done and it’s confirmed that it is good update. Then there will be 2 alternate models added over time. The stingray, and partisan 6 edition of this project. In a H and BL version
(beta note)
keep in mind at this moment this is a beta. meaning the 3d parts should be considered final. however with the new lock pin fire pin assemblies do I have to redo all my testing. so spring setting may chance after those days of testing are completed… also it does have a clear manual or now. but I will try to make some video’s when i have time explain this set further until I get around working finishing this package.
2-3-2024
new updated disconnect arm added for H based builds
for hammers and fire pins look at
https://www.printables.com/model/677286
compatibility
FGC-6H or FGC-6BL
you will need the base set from a FGC-6H or BL for this set
https://www.printables.com/model/557325-fgc-6h-mki-mki-hybid-mkii-mkiisd-1-on-1-airsoft-re
https://www.printables.com/model/400298-fgc-6bl-mkimkii-bolt-lock-starter-kit-gbb-airsoft-
it’s also highly recommended to use the lock pin fire pins assembly that is currently a beta
https://www.printables.com/model/677286
keep in mind that some buttstock’s options might not be compatible with this bolt. this still needs to be checked at this time.
these bolts can also be used for semi auto H or BL builds
__
how to use it
do keep in mind to only use the selector once the hammer is pushed down. other wise you will damage the it.
__
difference between a SF lower and the H(BL) lower
the only difference is that is got a cut out of the selectors so it’s more easy to got from full auto to semi auto. this can be done on a H(BL) lower but you will find that is not easy since you don’t have room to place your finger above the selector.
——
you can use this set in a view ways
the safe and full auto option
you can use it to make a H or BL model that can shoot only full auto
the benefit of this can be that the safety selector is a bit stronger that way
what do you need to remove from your H or BL
the semi auto disconnect part and it’s spring
what do you need to replace with the SF set
BOLT
spring cap
Full auto disconnect
hammer
the safe, semi auto and full auto option
what do you need to replace with the SF set
BOLT
spring cap
Full auto disconnect
the entire Fire control group
fire selector
hammer
lower (unless you don’t mind it’s harder to get the selector of the FA setting)
——
movie link:
FGC-6 turn the H or BL into a select fire model with the FGC-6SF parts set
https://youtu.be/cDxSzRmDxDM
FGC-6 turn the H or BL into a full auto model with the FGC-6SF parts set
https://youtu.be/WHMctS1RqiI
UNW FGC-6H FGC-6BL FGC-6SF Lower parts check for low friction movement
https://youtu.be/62I4DyG8WqM
FGC-6SF what to expect pre release of the 3d printable GBB closed bolt select fire airsoft replica
https://youtu.be/IRsZNzcXJ5E
a look at the prototype models:
FGC-6SF 3d printable GBB closed bolt select fire airsoft FGC-9 replica prototype
https://youtu.be/Z1AYAsQtHM4
FGC-6SF 3d printable GBB closed bolt select fire airsoft: prototype test fire Day 1
https://youtu.be/Glb9k_ty7rs
—-
materials needed (this text here will be updated until there is a official manual or parts list
links for that can be found here:
https://drive.google.com/drive/folders/1ppDKxs2tu0rj9MaRVWfpiozERtG7PVGz?usp=sharing
https://studio.youtube.com/video/62I4DyG8WqM/edit
hammer: parts are the same as for a BL / H
trigger: fallow the compression trigger parts of a BL / H
bolt spring: parts are the same as for a BL / H
full auto disconnect
1x spring:0.4mm wire, 5mm OD, 15mm long.
1x M2 bolt 12mm long
anti bounce bolt weight
10mm od metal rod 40mm long
-
note to printable users: you have to scroll down and also download all other files! to get you hands on the PDF’s
:format(webp)/https://fbi.cults3d.com/uploaders/14252661/illustration-file/5f6d4f14-4f82-4318-8ef3-cd71e990aafe/A_STOCK_MOD.jpg)
:format(webp)/https://fbi.cults3d.com/uploaders/14252661/illustration-file/142896d6-dd82-41d0-853d-b857ef8d6bbb/UNW-FGC-9_Magazine_Catch_Bar-E4.jpg)
:format(webp)/https://fbi.cults3d.com/uploaders/14252661/illustration-file/2357c935-2358-44ad-aa41-1947bf416944/FGC6-buttstock-set.jpg)
:format(webp)/https://fbi.cults3d.com/uploaders/14252661/illustration-file/2a2643d6-b338-4337-a986-0e24c6e9b78e/WE-TECH-G19-to-Menendez-v2--FGC9-mag-extender.jpg)
