MIKA3D 250g Bambu Lab AMS Spool Adapter
Copyright Claim
MIKA3D 250g Bambu Lab AMS Spool Adapter
Boost
21
25
33
Print Profile(1)
0.2mm layer, 2 walls, 15% infill
Designer
1.2 h
1 plate
Boost
21
25
33
2
69
114
Released
Description
This adapter system attaches to the edges of a MIKA3D 250g 134.5x44mm spool enabling usage within a Bambu Lab AMS.
Features:
- Reusable
- MIKA3D nameplate for easy identification when reusing
Instructions:
- Measure your spool first to ensure it matches the specified dimensions
- Print this model twice for a single spool
- Affix one spool adapter to each side of the MIKA3D spool
- See attached photos
Considerations:
- Print Material: Please print with a basic PLA or PETG to minimize any shrinkage.
Comment & Rating (33)
All
Print Profile
0.2mm layer, 2 walls, 15% infill
😍😍😍
The designer has replied
1
Reply
Thank you for sharing your make and rating! Did you have any issues with the model?
(Edited)1
Reply
Replying to @DesignCraft
yes... some filament... problems with the writing... but it could be the type of pla used
0
Reply
Replying to @mmggsetup
Thank you for the reply! Few suggestions: drying the filament helps improve prints, apply a heat gun or hairdryer for the light stringing (very briefly or you can warp the part), trim any heavy stringing with a utility knife or deburring tool. Lastly, I get great results using Bambu Lab's Textured PEI plate for most all of my prints. I highly recommend it. I hope this helps!
(Edited)1
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
came out great and works perfectly in the AMS. note!!! these also work perfectly with DO3D 250g spools too!
The designer has replied
1
Reply
Thank you for sharing your make and rating! Good to know that they're compatible with DO3D 250g spools also!
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Great. thanks
The designer has replied
1
Reply
Thank you for sharing your make and rating!
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
These are lighter weight and easier to use than the option I used to use and screw on, so I've started to phase them out for these new ones. Been printing them out of PLA+ and no issues so far.
The designer has replied
1
Reply
I very much appreciate the positive feedback! Thank you for sharing your make and rating!
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
didn’t fit
The designer has replied
0
Reply
Thank you for the feedback. Are your spools the same dimensions specified in the model description?
0
Reply
Yes, but for some reason they were about 1mm too big
0
Reply
Replying to @Emeegee
Thank you for the reply and helpful info. The inner diameter of the model, the area that wraps the spool, is 134.85mm in diameter which leaves a 0.35mm tolerance overall with a 0.175mm radius tolerance. They fit my spools perfectly as seen in the photos however there may be variances on the manufacturing side. I will keep an eye on this issue as hopefully some others provide feedback.
0
Reply
Do you plan to make an adapter to MIK3D 500g spools?
The designer has replied
0
Reply
Not at the moment but I'll comment back here and let you know if I do.
1
Reply
Thank you!
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
this is the most important part of my 3d printer,
(Edited)The designer has replied
1
Reply
Thank you for rating!
0
Reply
Boosted
Printed in PLA Basic on my X1C, on the Textured PEI plate, and it fit my new spool just perfectly.
The designer has replied
1
Reply
Awesome! Thank you for the positive feedback!
0
Reply
Boosted
Print Profile
0.2mm layer, 2 walls, 15% infill
perfect, exactly what I needed!! thank you so much for the file!!!!
The designer has replied
1
Reply
Thank you for rating!
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Worked great thank you!!!
The designer has replied
1
Reply
Awesome! Thank you for rating!
0
Reply
License
This work is licensed under a Standard Digital File License.
You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.
© 2024 MakerWorld