Amazon Echo Dot Alexa Dock Remixed by M. Owize

Remixed by

M. Owize

Hobby & DIY>Music

Print Profile(2)

All

A1 mini

P1S

P1P

X1 Carbon

X1E

0.2mm layer, 2 walls, 10% infill

Designer

8.4 h

1 plate

4.9(88)

visor cutout for ambient light sensor and buttons

1.8 h

1 plate

Boost

246

352

113

797

491

Released

Description

Support for Amazon Echo Dot Alexa

Echo Dot 4

Echo Dot 4 with clock

Echo Dot 5

Echo Dot 5 with clock

Echo Dot Width: 100mm

Echo Dot Height: 89mm

I was missing a fun stand for my Echo Dot. I modified the 3D mascot Phil aka Phil a ment to the size of the echo dot.

10-15% Infill Gyroid.

Use brim on the body. I used a 20mm outer edge to make sure it didn't fall off.

Enjoy!

Comment & Rating (113)

@stevenmohr653

Print Profile

0.2mm layer, 2 walls, 10% infill

Mit dem A1 mini und eSun RainbowLumiffekt gedruckt. Sehr cooles Gadget für den Amazon Dot 👍😁

The designer has replied

@M.Owize

Thanks <3 Your version is amazing !!

(Edited)

@Kirschi

Der leuchtet aber nicht wegen der Alexa selber, oder?

@stevenmohr653

Replying to @Kirschi :

ne der leuchtet wegen dem Filament

@CarGuy5811

Great print

(Edited)

The designer has replied

@M.Owize

Thanks a lot !!

@user_2400116416

Boosted

it came out amazing my daughter loves it!! Thanks for the design

@user_2585228971

Hello, how do you manage to have such a good surface without supports? The surface on the bottom of my backpack is bad. What temperature are you? Greetings Oliwer

The designer has replied

@M.Owize

Hello. looks like you used petg. I used pla with the settings included in the file.

@CarGuy5811

Print Profile

0.2mm layer, 2 walls, 10% infill

Looks Great!

@arthurreichert.

Print Profile

0.2mm layer, 2 walls, 10% infill

Very nice and smooth print! I printed it with PETG and it does glow when talking to Alexa, looks gorgeous.

@Anniiluff

Print Profile

0.2mm layer, 2 walls, 10% infill

sehr schön geworden ☺️

@user_337671244

Print Profile

0.2mm layer, 2 walls, 10% infill

sieht super aus

@Fak3do

Boosted

Print Profile

0.2mm layer, 2 walls, 10% infill

perfect!!

@3dlyx

There has been done quite a bit of work in this remix. It is not as versatile as it could be, as the alignment does depend on the variation of the echo. That could have adressed with a wider slot in back to connect the echo's cable. My version does fit perfectly though. The visor on the other hand blocks the ambient light sensor and the physical push buttons, resulting in the brightness of the clock to be stuck at the lowest level. A simple cutout again solves that problem as well (see print profile) but a bit at cost of the aesthetics. But form follows function. Same goes for the echos light circle, that now only is visible in white or very light filaments. Solution? You guessed it: cutouts probably. Except for the sensor issue, those points didnt bother me enough to change and reprint the mascot itself. Si in total I would give 3.5 Stars, but rather chose not to rate at all in order to not lower your rating average. I still enjoy the conecpt and the model as well as the final result a lot.

This remix is based on

MatterHackers' Mascot Phil A Ment

License

This work is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

Print Profile(2)

Description

Support for Amazon Echo Dot Alexa

Comment & Rating (113)

This remix is based on

License

Related Models

Amazon Echo Dot Gen 4 Stand Alexa

der Boden Micky Maus Alexa Echo Dot4 Mickey Mouse

die Ohren Micky Maus Alexa Echo Dot4 Mickey Mouse

Panda Echo dot 4 holder