Der Inhalt ist zu lang und wurde abgeschnitten
HINWEIS! Bitte druckt diesen Blaster recht Farbenfroh, so dass er sich stark von echten Waffen unterscheidet.
Nachdem ich bereits vor ein paar Wochen meine EU Version des CALIBURN 4 Blasters veröffentlicht habe, folgt nun meine umgezeichnete Version des Orion Blasters LYNX. Es gab bereits eine metrische Vorlage, jedoch konnte ich dennoch kaum Teile aus dem DIY Handel oder diverser Onlinehändler verwenden, weshalb diese Version entstand. Darüber hinaus habe ich noch die folgenden Add-Ons mit integriert (in STEP File enthalten):
Alle integrierten Dateien wurden auf mein Modell angepasst.
Einige der Alu Flachprofile müssen noch gebohrt werden und benötigen ein M3 Gewinde geschnitten um sie miteinander verschrauben zu können. Ich empfehle die STEP Datei als Hilfestellung für die genauen Maße zu verwenden.
Die 457 mm Transfer Bar muss zusätzlich noch ausgeklinkt werden. Ich habe hierfür eine Schablone zum Anzeichnen angefertigt und das Ganze mit dem Dremel und einer Trennscheibe bewerkstelligt. Zusätzlich muss die Feder noch gekürzt werden. Dies lässt sich ebenfalls sehr gut mit dem genannten Dremel Setup bewerkstelligen. Für den Rest des Aufbaus kann man sich an die Anleitung von Out of Darts halten. Jedoch habe ich anders als in der Anleitung den Plunger von hinten eingesetzt, da von vorne der Rail Shroud stört.
Wie schon bei der Caliburn, habe ich weitestgehend versucht mit Einschmelzmuttern der Größe M3 zu arbeiten und darauf geachtet, dass ihr die Hardware komplett im DIY Handel bekommt um den Preisrahmen nicht zu sprengen. Das Alurohr und sämtliche Schrauben, Muttern und kleine Federn habe ich beim regionalen HORNBACH einzeln gekauft oder im Onlineauktionshaus geordert.
gekürzt auf folgende Maße:
zugeschnitten auf:
zugeschnitten auf:
Die beiden Federn (K25 & K31) werden ineinander gesteckt um so möglichst nah an der Original angebotenen zu sein.
gekürzt auf:
Optional für EX-BCAR:
Optional für Shade Vertical Foregrip:
Zur besseren Übersicht und für mögliche Anpassungen hänge ich meine STEP Datei ebenfalls mit an.
PRINT SETTINGS
Gedruckt aus ABS von CR-3D
Blau = ABS Wasserblau Magic
Grau = ABS Carbon
Orange= ABS Neon Orange
4 Wände
4 Boden
4 Top
40% GITTER / GRID
0.2 Layerhöhe
Bei Fragen dürft ihr mich gerne Anschreiben!
Bin schon sehr auf eure Makes gespannt.
NOTE! Please print this blaster quite colorful, so it will differ a lot from real weapons.
After I already published my EU version of the CALIBURN 4 Blaster a few weeks ago, now follows my redrawn version of the Orion Blaster LYNX. There was already a metric template, but I still could hardly use parts from DIY stores or various online retailers, which is why this version was created. Furthermore I integrated the following add-ons (included in STEP file):
All integrated files were adapted to my model.
For all those who do not know the LYNX Blaster yet, I can highly recommend this video.
Some of the aluminum flat profiles still need to be drilled and need a M3 thread cut to be able to screw them together. I recommend using the STEP file as a guide for the exact dimensions.
The 457 mm transfer bar also needs to be notched. I made a template for this and did the whole thing with the Dremel and a cut-off wheel. In addition, the spring must be shortened. This can also be done very well with the aforementioned Dremel setup. For the rest of the setup, you can follow the instructions from Out of Darts. However, unlike the instructions, I inserted the plunger from the rear, since the rail shroud interferes with the front.
As with the Caliburn, I tried to work with M3 heatset inserts and made sure that you can get all the hardware in DIY stores so as not to break the price range. The aluminum tube and all the screws, nuts and small springs I bought individually at the regional HORNBACH or ordered in the online auction house.
shortened to the following dimensions:
cut to:
cut to:
The two springs (K25 & K31) are inserted into each other to be as close as possible to the original offered.