Cardboard Adapter (light weight)
Remixed by
Copyright Claim
Cardboard Adapter (light weight)
Remixed by
Boost
19
36
31
Print Profile(3)
one.Half
Designer
1.1 h
1 plate
OneHalf and TwistLock - 0.2mm layer, 4 walls, 15% infill
Designer
2.2 h
1 plate
only.TwistLock
Designer
1.2 h
1 plate
Boost
19
36
31
0
102
216
Released
Description
It's the lightweight version of Manufakturs adapter. The adapter is suitable for 650g, 1kg and 1.1kg cardboard reels. One half weighs only 27g. A screw and two adapter halves (a set) weigh a total of only 87g The handling of the screw is also improved. The thumb nestles better.
It can be used for Spoolroller, AMS and HydraAMS.
spool
spooladapter
bobbin
bobbina
bobbine
adapter
cardboard
jayo
eryone
elegoo
creality
pappspule
cardboard spool
cardboard spool adapter
cardboard spool adapters
overture
esun
cardboard fixing
cardboard bobbin
apdapter
pappe
kartonspule
karton
bio
sustainable
sustainably
sustained
nachhaltig
lightweight
light
mini
low weight
ams
hydra
hydraams
spoolroller
Comment & Rating (31)
All
Print Profile
OneHalf and TwistLock - 0.2mm layer, 4 walls, 15% infill
great fit and easy print
The designer has replied
0
Reply
I'm glad that everything works with the print profile, interesting filament color.
Thanks for rating it!
0
Reply
Print Profile
OneHalf and TwistLock - 0.2mm layer, 4 walls, 15% infill
fits perfectly
The designer has replied
1
Reply
Thank you for your feedback
0
Reply
Print Profile
one.Half
fits perfectly
The designer has replied
1
Reply
Thank you for your feedback
0
Reply
Print Profile
OneHalf and TwistLock - 0.2mm layer, 4 walls, 15% infill
tried to run several time on p1s and could get past first layer. never had an issue like this
(Edited)The designer has replied
0
Reply
You should calibrate your printer instead of giving the profile a bad review.
All the other 119 users have printed it with this profile with no problems.
Edit:
Choosen your own filament?
Calibrated it?
Calibrated the printer?
Calibrated flushing?
Which filament did you use?
(Edited)1
Reply
Download, slice, print. No problems.
Don't use speed modes!
0
Reply
Print Profile
one.Half
Passt leider nicht auf meine Papprolle. Ansonsten spitzenmäßig Arbeit. Vielen Dank
The designer has replied
0
Reply
Hi, please send a photo. Maybe I can help!
0
Reply
Print Profile
OneHalf and TwistLock - 0.2mm layer, 4 walls, 15% infill
passt noch auf die spule. Das kann man aber alles selbst erledigen
The designer has replied
0
Reply
Hi, please send a photo. Maybe I can help!
0
Reply
Print Profile
OneHalf and TwistLock - 0.2mm layer, 4 walls, 15% infill
Printed great. Didn't work for me though.
The designer has replied
0
Reply
What does that mean in detail?
You need 2 halves and screw them against a cardboard spool.
0
Reply
Tried this with Elegoo and Sun Card board spools and was too small to go around the spools. Without being able to slip over end of card board spool it wasn't able to fit correctly in AMS cleanly and was just a little too wide. Maybe the cardboard spools now are slightly closer to the 200 mm on those two brands. I had hoped this would finally allow me to finally stop respooling cardboard spools.
0
Reply
Print Profile
one.Half
works great for 250g spools!
0
Reply
Print Profile
OneHalf and TwistLock - 0.2mm layer, 4 walls, 15% infill
These are the best cardboard adapters that I have used. They do not run the risk of slipping off like other cardboard adapters tend to do. An added benefit is that it works with cardboard spools from a variety of manufacturers and the desiccant hub adds even more functionality.
0
Reply
This remix is based on
License
This work is licensed under a
Creative Commons Attribution-Noncommercial-NoDerivatives
© 2024 MakerWorld