Poop Pop Stop Large for P1S/P1P
Remixed by
Copyright Claim
Poop Pop Stop Large for P1S/P1P
Remixed by
Boost
409
799
404
Print Profile(6)
0.16mm layer, 3 walls, 15% infill
Designer
35 min
1 plate
0.16mm layer, 4 walls, 15% infill PETG
31 min
1 plate
PLA - pla in P1P works just fine!
23 min
1 plate
0.16mm layer, 4 walls, 15% infill ABS
29 min
1 plate
Click to see more
Boost
409
799
404
13
2 k
1.6 k
Released
Description
I remixed this model because I found it very useful, I had the problem that the waste stopped between the perimeter of the waste tray and the perimeter of the molded piece, I enlarged the waste space so that I could let the waste fall comfortably. Now I no longer have waste material on the print bed!
Thanks Downhill_Solutions!
Comment & Rating (404)
All
Print Profile
0.16mm layer, 3 walls, 15% infill
It's a nice construction in itself, but unfortunately the poop shoot gets stuck. I tested it several times.
The designer has replied
1
Reply
do you have x1c or p1 series?
0
Reply
Replying to @spluca80
I have a X1C.
0
Reply
Replying to @Krall3
I haven't tried it on the X1C, if I can I'll try it and see if there are any changes to make. Thanks for the feedback
0
Reply
Print Profile
PLA - pla in P1P works just fine!
A great model. Fits well, just a bit finicky to insert.
2
Reply
very tight fit
(Edited)1
Reply
Boosted
Print Profile
0.16mm layer, 3 walls, 15% infill
I printed with PETG and removed the rafts and still printed flawlessly. Supports did also remove without any issue. Seems to work, so far. Thanks!
The designer has replied
1
Reply
Nice color!
0
Reply
Print Profile
0.16mm layer, 3 walls, 15% infill
work great
The designer has replied
1
Reply
Thankyou!
0
Reply
Print Profile
0.16mm layer, 4 walls, 15% infill PETG
A great utility, it's gone on all three of my printers!
Printed out of orange PETG.
Pics are after over a month and hundreds of poops, only have had a handful of chute clogs, though I'm sure this has improved that statistic, I have noticed far fewer poos falling onto the bed plate when this is installed.
Also, I have not had any issues with higher temp filaments sticking to the petg. Thought that might have been an issue but it has not been!
2
Reply
Print Profile
0.16mm layer, 3 walls, 15% infill
Top, Test mit 10 Layerwechsel 10/10 da gelandet wo sie sollen, und zwar in die Toi und nicht aufn Druckbett.
Gedruzckt auf ein P1S mit ABS
The designer has replied
1
Reply
TOP!
0
Reply
Print Profile
0.16mm layer, 3 walls, 15% infill
严丝合缝 很不错。
2
Reply
printed the original in PLA but poops stick to it and it’s not working well because of
that but not poops inside the printer since installed. perhaps need to have a larger hole for pooping like your remix and it will not stick. nice design , I will give a try thanks a lot
(Edited)
The designer has replied
0
Reply
hello, print this remix in PETG, ASA or ABS; pla is not recommended
1
Reply
remix
works great
thanks
0
Reply
Print Profile
0.16mm layer, 3 walls, 15% infill
flawless print, perfect fit into the printer
The designer has replied
0
Reply
woooowwww good print!
0
Reply
Print Profile
0.16mm layer, 3 walls, 15% infill
great!
The designer has replied
0
Reply
thankyou
0
Reply
This remix is based on
The model does not exist anymoreLicense
This work is licensed under a
Creative Commons Attribution-Noncommercial-Share Alike
Related Models
© 2024 MakerWorld