A1 Mini Tool Tray for A1 mini tool box Remixed by PF3d_designs

Remixed by

PF3d_designs

3D Printer>3D Printer Accessories

Print Profile(3)

All

A1 mini

P1S

P1P

X1 Carbon

X1E

Full Build with tool box and tools 0.2mm layer,

Designer

7.7 h

5 plates

4.9(17)

no logo 0.2mm layer, 2 walls, 15% infill

Designer

2.5 h

1 plate

4.3(6)

just the tray with logo and color change 0.2mm layer, 2 walls, 15% infill

Designer

2.9 h

1 plate

5.0(3)

Boost

194

195

Released

Description

I liked https://makerworld.com/en/u/3041365136 tool holder but I've been making my own hotend holder that matches the hotends like a

glove so i figured I would adapt my Holders over to save a little space and also add back the Bambu logo as well.

Go check out the orginal you will probably like it better it also holds the silicone socks better
https://makerworld.com/en/models/81829

The tool box can be found here
https://makerworld.com/en/models/81829

The lid I used can be found here
https://makerworld.com/en/models/86106

I used these pins instead of the m3 screws
https://makerworld.com/en/models/86465

Comment & Rating (33)

@GAZbot

Print Profile

no logo 0.2mm layer, 2 walls, 15% infill

printed with default settings but tolerances were too tight. struggled removing hotend when inserted.

The designer has replied

@PF3d_designs

the hotends are supposed to be very tight I have intended to make a wall mount and thus a tight fit so they don't remove themselves although I still haven't gotten around to it. Either way thanks for the feedback.

(Edited)

@Henryb2015

Print Profile

no logo 0.2mm layer, 2 walls, 15% infill

athis file worked perfectly for what I needed. I added some Honeycomb mounts on the back to put on honeycomb wall. (see pictures) I printed with a .2mm layer height and a 15% infill.

The designer has replied

@PF3d_designs

Looks good!

@Neiljt

Print Profile

Full Build with tool box and tools 0.2mm layer,

I had no issues printing this albeit for a different box .

The designer has replied

@PF3d_designs

Looks great!

@ryanhartle

Print Profile

Full Build with tool box and tools 0.2mm layer,

We have had the A1 mini since Christmas, gift for our kids, but I have been enjoying it just as much as they have and finally decided to print a toolbox for the tools and few accessories. This printed fantastic and looks great. What I really liked about this one is that no extra hardware was needed to be purchased, everything is printed!!!

@Mortemar

Print Profile

no logo 0.2mm layer, 2 walls, 15% infill

(Edited)

Other Issues:Don't take my comment into account, I'm a bitter idiot! >>>A lot of filling for nothing, the slot are too small not well designed for standard-sized humain hands. Not even half the toolbox fit inside, the printhead slot are nice but they're at the exact size and it's very hard to get a new head inside, a used one don't feet and it's almost impossible to get them out delicately because it's very tight. I threw it away a few minutes after the end of the print, didn't have time to cooldown.

The designer has replied

@PF3d_designs

Sorry you feel that way the tool slots are tight but they still work well i use mine almost daily, the hotends are supposed to be very tight I have intended to make a wall mount and thus a tight fit so they don't remove themselves although I still haven't gotten around to it. Either way thanks for the feedback and sorry for your loss.

(Edited)

@Mortemar

hello, don't feel sorry, it's all my fault. i should have paid attention and read the information on your post properly instead of printing it out straight away without being sure of what i really needed. besides, i think i'm being really rude for nothing, it's all on me.