Laptop stand V2 by Libb_s

Libb_s

Tools>Gadgets

Print Profile(6)

All

P1S

P1P

X1 Carbon

X1E

PLA 0.28mm layer, 2 walls, 15% infill

Designer

3.4 h

4 plates

4.9(107)

PETG 0.28mm layer, 2 walls, 15% infill

Designer

3.9 h

4 plates

4.9(24)

0.4mm nozzle, 0.1mm layer, 4 walls, 15% infill, X1C AMS Version

4.7 h

3 plates

5.0(8)

0.28mm layer, 2 walls, 15% infill PETG

4 h

4 plates

5.0(2)

Click to see more

Boost

383

662

155

1.4 k

2.5 k

Released

Description

Design upgrade version Laptop stand.

No need for AMS.

Comment & Rating (155)

@saemann.m

Print Profile

PLA 0.28mm layer, 2 walls, 15% infill

Noch mit Gummipuffern versehen - top.

@Cdude03

Print Profile

PLA 0.28mm layer, 2 walls, 15% infill

Amazing model, printed without a problem. However, the triangle color fill pieces bulged a bit and it seemed like it was too long, so I fixed it by making small cuts. I do not believe it was the model, but the fact I that I printed everything except the color fill out of black ABS, and used silk copper PLA for the color fill. The cuts are hardly noticeable and the whole stand is well designed.

The designer has replied

@Libb_s

if you used ABS also for the color filling, then it must be ok. ABS has greater shrinkage than PLA

(Edited)

@KD3D

Print Profile

PETG 0.28mm layer, 2 walls, 15% infill

Perfect print with PolyLite PETG

(Edited)

The designer has replied

@Libb_s

good job ☺️

@dki_42

Used for my M2 macbook air. Have not found better design than this. THX.

@Dongodor

Boosted

Print Profile

PETG 0.28mm layer, 2 walls, 15% infill

Made it in PETG Basic for the frame and PLA Matte for the color insert and it looks awesome ! I also used glu to solidify it

@TaggingHash

Print Profile

PLA 0.28mm layer, 2 walls, 15% infill

Turned out great! Love the design!

@Fearless2325

Boosted

Print Profile

0.6mm nozzle, 0.3mm layer, 2 walls, 15% infill

Printed amazing and snaps together perfect! I love this!

@strawberrypoppi

Print Profile

0.4mm nozzle, 0.1mm layer, 4 walls, 15% infill, X1C AMS Version

Good. and easy to print.

@strawberrypoppi

Print Profile

PLA 0.28mm layer, 2 walls, 15% infill

looks good. easy to print. printed the main frame in ABS cf. the rest in pla. loves the look of it. except the angle is a little too steep to use. wrist aching after some time. haha.

@Noodle_Doodler

Print Profile

PLA 0.28mm layer, 2 walls, 15% infill

Profile works! Overall recommended with a few caveats. There was a little bit of warpage from bed removal on main frame but could have been user error. I would have liked the frame flipped to have the textured/ smooth side facing out for better asthetics. Most of the trim fit in perfect, but the thin trim was difficult. I may reprint and test again. I'd suggest smoothing out the tops if you have that setting on your printer. Either way, it's a badass looking stand!