Poop Pop Stop smooth with Logo for P1S/X1C/P1P
Remixed by
Copyright Claim
Poop Pop Stop smooth with Logo for P1S/X1C/P1P
Remixed by
Boost
78
180
94
Print Profile(2)
LOGO 1 0.16mm layer, 4 walls, 15% infill
Designer
35 min
1 plate
LOGO 2 0.16mm layer, 4 walls, 15% infill
Designer
36 min
1 plate
Boost
78
180
94
1
356
297
Released
Description
IF YOU LIKE THIS MODEL GIVE ME A “THUMBS-UP” SO MORE PEOPLE CAN DISCOVER THIS MODEL. THANKS
UPDATE!! I ADDED A SECOND MODEL WITH DIFFERENT LOGO FOR BETTER VISIBILITY
I Remixed the perfect Working piece from @downhill_Solutions and @spluca80
I made it more smooth for better looking, and of course added our Favourite Brand Logo.
I had the problem that the waste stopped between the perimeter of the waste tray and the perimeter of the molded piece, I enlarged the waste space so that I could let the waste fall comfortably. Now I no longer have waste material on the print bed!
Comment & Rating (94)
All
Print Profile
LOGO 1 0.16mm layer, 4 walls, 15% infill
fits great
The designer has replied
1
Reply
thanks for Rating. I Hope u enjoy!
0
Reply
Print Profile
LOGO 1 0.16mm layer, 4 walls, 15% infill
The designer has replied
1
Reply
Good Print ! Would you mind i use your Picture as Profile Picture ?
0
Reply
Replying to @VroDoPrints
No problem, you are welcome to use the image.
(Edited)1
Reply
Print Profile
LOGO 1 0.16mm layer, 4 walls, 15% infill
The designer has replied
1
Reply
thank you for Rating! i hope you enjoy it.
0
Reply
Print Profile
LOGO 1 0.16mm layer, 4 walls, 15% infill
i am going to look for another solution. this is not working properly. the filament got stuck on the 3d print and to the hot end.
The designer has replied
0
Reply
can you tell me wich Printer and Filament u useing ?
0
Reply
I have 2 x1 Carbon and printed them with Bambu Lab filament. I printed two of them for my 2 Bambu Lab X1 Carbon.
one of them created a large clog of filaments that was difficult to remove.
I have removed both from the two x1 Carbon.
0
Reply
Print Profile
LOGO 1 0.16mm layer, 4 walls, 15% infill
Prints very well and does seem to help direct the poops down the chute. I've still had a couple end up on the build plate, but far less than I had before
The designer has replied
1
Reply
thank you for Rating 5⭐️
would love to See your results 🤘🏻
0
Reply
Print Profile
LOGO 1 0.16mm layer, 4 walls, 15% infill
love it!
The designer has replied
1
Reply
thank you for Rating 5⭐️
would love to See your results 🤘🏻
0
Reply
with the new update this doesnt work anymore
The designer has replied
0
Reply
what exactly isn’t working? if you mind tell me maybe I can fix it 👍🏻
0
Reply
it stops now 2mm near by the wiper and drop some material and that can go down and stuck betwen the wiper and the part.
0
Reply
Print Profile
LOGO 1 0.16mm layer, 4 walls, 15% infill
dieser ist die beste Ausführung, da beim Original der Raum für den Poop zu klein ist und dann dieser dort hängen bleibt, hier wurde der Raum etwas vergrößert und somit ist genügend Platz auch für Poops bei größerer Reinigung 👍
The designer has replied
1
Reply
Ich danke dir für die Positive Bewertung! Happy Printing!
0
Reply
Print Profile
LOGO 1 0.16mm layer, 4 walls, 15% infill
Came out great in ABS and doing it´s work very good
The designer has replied
1
Reply
Thanks for Rating! I hope you Enjoy
0
Reply
Print Profile
LOGO 1 0.16mm layer, 4 walls, 15% infill
no more problems with poop on the plate 👍🏻👍🏻👍🏻
1
Reply
This remix is based on
License
This work is licensed under a
Creative Commons Attribution-Noncommercial-Share AlikeRelated Models
© 2024 MakerWorld