Arcade For Switch Mk1 and Oled With Buttons Board Remixed by SaD_DidaS

Remixed by

SaD_DidaS

Toys & Games>Board Games

Print Profile(1)

All

X1 Carbon

P1S

P1P

X1E

0.2mm layer, 2 walls, 15% infill

Designer

21.8 h

8 plates

4.7(10)

Boost

138

256

499

Released

Description

The plate 4 is for the non Oled version .

Print on place , 15% infill , no supports required

Please clean your Bed thoroughly and check that it fits properly.
Some failures may occur.

Enjoy ;)

Comment & Rating (33)

@B34rdm4n

Print Profile

0.2mm layer, 2 walls, 15% infill

Nice! Thank you

The designer has replied

@SaD_DidaS

glad you like it :) I had a lot of fun printing it myself ^^

(Edited)

@Timdorsett

Replying to @SaD_DidaS :

how to put together

@SaD_DidaS

Replying to @Timdorsett :

follow your instinct, it's very simple ;)

@flashtu1980

Boosted

the Joystick panel is to long only 180mm will fit. otherwise nice print but quality would way better in slower speed i used 100mm/s all.

The designer has replied

@flashtu1980

Boosted

Replying to @SaD_DidaS :

i print everything like it was in the profile i changed nothing.

@SaD_DidaS

Replying to @flashtu1980 :

I'm sorry for you, because this is the first time we've made the remark. I'm the designer and printer, I don't know what's going on with you.

@SaD_DidaS

Replying to @flashtu1980 :

i'm modify my profile with new board dimension ;) thx

@PatrikFehr

Print Profile

0.2mm layer, 2 walls, 15% infill

The designer has replied

@SaD_DidaS

Nice!

@SaD_DidaS

Looks great !!

@Fatalchaos25

Boosted

I made it all different colours for my little girl and put her name on the front

@Woogie

This is not "Print on/in place". Can you please explaine the difference between this and the original? Did you just add the arcade stick part to a build plate, so that it's an all-in-one download? Thanks :)

The designer has replied

@SaD_DidaS

Bonjour, c'est a imprimer sans aucun support je l'ai fait moi même,le modèle de la photo . L'original n'avait pas le mondèle pour la version oled de la Switch, "l'original" a repris mon modèle oled , et les bouton sont aussi ma création que " l'original" as aussi repris. a vous de vous faire un avis :) vous pouvez exporter les profils en stl séparément, je vous laisse prendre connaissance des fonctions du slicer .

@Woogie

Replying to @SaD_DidaS :

ok, thank you for the info :)

@Timdorsett

how to put together

The designer has replied

@SaD_DidaS

follow your instinct, it's very simple ;)

@SaD_DidaS

Hello , just glue it together

@para

Printing this right now and chose this one because it has the cool joysticks and also mentioned it fit the OLED version. Couple things people might want to know before printing: - I added supports on the red/white and blue/white pieces because when I started to print the blue piece without them it starts off as two pieces and eventually joins into one. Well my smaller/thinner piece started to curl so I cancelled, cleaned the plate, added glue, added supports, and tried again. Short version: use glue, use supports on those pieces - Don't bother printing the arch on plate four. The arch on plate four is for the non-oled version. I didn't realize until after I had already printed it and so wanted to potentially prevent someone else from wasting any more plastic I'll let you know if I come up with any other bangers to take note and then upload a picture when I'm done!

The designer has replied

@SaD_DidaS

vous avez raison de le souligné , mais à mon sens les personnes doivent bien évidement vérifier se qu'ils impriment, en se qui concerne les support , il n'est pas necessaire si votre addésion est pauvre veuillez la vérifier cela ne viens pas du modèle. Bonne journée

@lepeter0

Print Profile

0.2mm layer, 2 walls, 15% infill

The designer has replied

@Kevfarrell52

did you print this? is adhesive required to construct this? Thanks

(Edited)

@SaD_DidaS

Replying to @Kevfarrell52 :

The elements are glued with cyanolit glue only, but be careful with the black parts, this can leave white marks once dry. It is best to use contact glue.

@lepeter0

this was printed fine

@Fatalchaos25

Boosted

nice model im on printing now