AMS Wall Mounts (V2.0) [Fits all AMS versions] by Roland Deschain

Roland Deschain

3D Printer>3D Printer Accessories

Print Profile(2)

All

X1 Carbon

P1S

P1P

X1E

(Fit Test Piece) 0.28mm layer, 2 walls, 15% infill

Designer

34 min

1 plate

5.0(3)

(Strong) 0.2mm layer, 6 walls, 25% infill

Designer

13.3 h

2 plates

4.9(8)

Boost

Released

Description

This design is heavily inspired by the Wallmount for Bambu AMS model created by StefanWoX. I wanted my AMS unit slightly further from the wall and saw room for improvement so I spun up my own.

This version is stronger than my original version and better supports the full length of the AMS. The AMS unit will sit ~65mm from the wall with these mounts which will allow you to fully open the lid.

The wall mounting holes are identical to the original version so you can easily upgrade for more support.

Testing

I've included a test model so you can quickly print out a low quality piece to ensure the key parts will fit with your AMS unit. The end of the test piece will roughly be flush with the back of the AMS unit. If the test piece doesn't fit for you please message me so I can update the model.

Assembly

You will need (6) M4 x 20 cap screws and nuts to attach the shelf piece to the bracket.

The holes for mounting the bracket to the wall have a diameter of 6mm with a head diameter of 12mm and a head depth of 2mm. I used some heavy duty drywall anchors from Home Depot to mount mine.

Updates

2024-04-21: Removed the second from last wall in order to fit both 3-slot variants.

Warning: If you print a third party profile you may not be getting the latest version or the highest quality print.

If you like this project, please don't forget to ❤ Like and ★ Rate!

* Some of the links above are Amazon Affiliate links

Comment & Rating (26)

@zE____

not all

The designer has replied

@RolandDeschain

Hi @zE____ when did you purchase your AMS? I'm not sure I have encountered that body yet but am curious if it would work if you shifted the bracket left in your photo to start at the second rectangular slot. If that doesn't work feel free to shoot me a message so I can get some measurements from you.

@zE____

Replying to @RolandDeschain :

Moving back one grid is useless, The rear of the AMS will come up to the shelf. I purchased it in China in September 2022, and it is estimated to be the first version. I used a translator, but I don't know if you can understand.

@user_1285851921

It does not fit with the 3 slot. I printed the test piece and no go.

The designer has replied

@RolandDeschain

I'll send you a message to get more details.

@AeonJoey

Darn, same here ;_;

@AeonJoey

here's mine next to the test print just in case :)

@daniel.fiorica

Print Profile

(Strong) 0.2mm layer, 6 walls, 25% infill

solid design, feels very sturdy with a fully loaded AMS.

@Cheddar

Boosted

Print Profile

(Strong) 0.2mm layer, 6 walls, 25% infill

These supports are amazing!! I printed them in red PETG. I took the brackets with me to the hardware store and found the right sized screws. This saved time and money over many furniture options that I didn’t like as much.

@VCP3D

Print Profile

(Strong) 0.2mm layer, 6 walls, 25% infill

Excellent 👍🏻 Danke für das gut durchdachte Design und das Upgrad!

@Tekcor

I’ve tried multiple times to get a good print of this, but no matter what I try, the corners peel off the build plate. Even with the author’s profile. I’m just flushing filament down the toilet at this point.

The designer has replied

@RolandDeschain

@McGrath what type of filament are you using? I didn't have any issues with bed adhesion on this model? I like to use Magigoo for additional bed adhesion (https://amzn.to/3xlkFYA). You could also try adding a manual brim on the "Others" tab but it really shouldn't be necessary for this model.

@Tekcor

Replying to @RolandDeschain :

Bambu Basic PLA on a textured PEI plate set to 65C in an enclosed P1P. Even with a 10mm brim, it either pulls up the brim or detaches from the brim.