Printing Information:
Iβve designed the components into multiple segmented part options to allow the makersβ to select the best part model option based on their particular printerβs bed size. Note: all required components can be printed on a bed as small as 150mm x 150mm.
Note: All models are pre-positioned in the recommended printing orientation.
Parts to Print
Frame Carriage Components
(4 pcs. Center Frame Design)
Frame Four Piece Left - (3 pcs.)
Frame Four Piece Left Cent. - (3 pcs.)
Frame Four Piece Right Cent. - (3 pcs.)
Frame Four Piece Right - (3 pcs.)
(2 pcs. Center Frame Design)
Frame Two Piece Right - (3 pcs.)
Frame Two Piece Left - (3 pcs.)
(3 pcs. Center Frame Design)
Frame Three Piece Center - (3 pcs.)
Frame Four Piece Right - (3 pcs.)
Frame Four Piece Left - (3 pcs.)
(1 pc. Center Frame Design)
Frame Single Piece - (3 pcs.)
(Frame End)
Frame End - (2 pcs.)
Frame End R Ear - (2 pcs.)
Frame End L Ear - (2 pcs.)
Spindle Components
(2 pc. Spindle design)
Spindle Half - (8 pcs.)
Locating Ring - (4 pcs.)
Flange - (8 pcs.)
Support - (8 pcs.)
(Spindle design with 8mm dowel)
Spindle Whole - (4 pcs.)
Flange - (8 pcs.)
Support - (8 pcs.)
Spacer Components
(4 pc. Per Side design)
Spacer Center Right - (2 pcs.)
Spacer Center Left β (2 pcs.)
Spacer End - (4 pcs.)
(3 pc. Per Side design)
Spacer Center β (2 pcs.)
Spacer End β (4 pcs.)
Optional Wall Mount
Wall Mount Top β (1 pcs.)
Wall Mount Lip β (1 pcs.)
Bottom Wall Mount β (1 pcs.)
Note: recommend printing the wall mount components with PETG for increased layer adhesion. If this is not possible PLA or even ABS (donβt forget to adjust the model scale in your slicer to compensate for shrinkage if using ABS) will suffice but you may notice layer separation on the upper mount developing over a period of time that may require reprinting the Top Wall Mount again.
Print Profile Settings
Printer: Qidi X-Pro
Material: Hatchbox PLA Black (Overture White PETG for Wall Mounts)
Print Temp: 185 C (225 C for PETG)
Nozzle: 0.4 mm
Layer Height/Resolution: 0.3 mm
Infill: 15%
Print Speed: 60.0 mm/s
Raft: No
Supports: No
Print Time and Material Usage (estimated based on four piece frame and three piece spacer designs)
Frame Assy. each (4 pieces) - Time: 3:53 Hrs. β 45g. - 15.15m (x3)
Frame Ends Complete (2@ Frame Ends, 4@ Frame End Ears) - 3:50 Hrs. β 42g. β 14.21m
Spindle Halves (8 each) β 6:45 Hrs. - 91g β 30.66m
Locating Rings (4 each) β 0:18 Min. β 3g β 1.10m
Flanges (8 each) β 1:45 Hrs. β 21g β 7.14m
Supports (8 each) β 4:17 Hrs. β 45g β 15.07m
Spacers (2@ centers, 4@ ends) β 3:31 Hrs. β 37g β 12.39m
Total Estimated Print Time: - 32:22 Hrs.
Estimated Material Usage: - 377 grams β 127.09 meters
Please reference the included Assembly Instructions.pdf file for assembly information.
Additional Notes:
: Recommend printing a minimum of 3 walls on the Spindle axle (top of Spindle).
: When printing the spindle halves, if possible, use a variable infill or some other available means so that the axle area (top) has a higher infill density than the lower larger dia. section. The reason is that if you select let's say 15% infill, although adequate for the lower larger section would result in hardly any infill within the top smaller axle dia. section. Refer to your particular slicer for infill options that may be available to you.