Automag .44 Prop/Replica Gun by BrewBoy

BrewBoy

Props & Cosplays>Replica Weapon

Print Profile(1)

All

P1P

P1S

X1 Carbon

X1E

0.16mm layer, 3 walls, 15% infill

Designer

11.4 h

2 plates

5.0(2)

Boost

146

209

250

Released

Description

Automag .44 prop gun with moving parts:

This was a quick model I made to help hone my skills. A pretty good look-a-like of the Automag .44 but I realized to late that I forgot to give it a hammer. Oops. I hope you enjoy it anyway.

STEP files have been included for your remixing pleasure.

Features:

Moving slide.
Working magazine and magazine release.
Moving trigger.
Folding rear sights.

Hardware Required:

1 x M3*10 mm bolt.

1 x M3*14 mm bolt.

1 x M3*16 mm bolt.

2 x M3*20 mm bolt.

1 x M3*22 mm bolt.

4 x M3 nut.

2 x Pen Springs (For magazine catch & trigger)

1 x Compression Spring: OD - 10 mm, WD - 0.6-0.8 mm, Length - 65 mm (For the slide)

Super Glue (For grip panels)

Step 1: Superglue pen spring to the back of the trigger, push into the lower frame and secure with a bolt and nut.

Step 2: Push the paddle alignment pins through the holes in the grip paddles. Apply super glue to the backs of the paddles and place them on the sides of the lower frame.

Step 3: Push an M3 x 12 mm bolt through the hole in the left side of the frame, and place a pen spring over the protruding part in the magazine catch slot. Place the magazine catch in the slot and tighten the bolt until the catch slide backwards and forwards easily. This can be adjusted to your preference.

Step 4: Place the Barrel/upper frame onto the lower frame and secure with a bolt and nut.

Step 5: Slide the compression spring into the slot int the bolt, then place the spring follower into the bolt with the hole in it facing directly upwards. Slide the bolt assembly into the back of the upper frame.

Step 6: Use an M3 x 20 mm Bolt to secure the upper frame to the spring follower. Test your slide/bolt by pulling it back and seeing if it snaps forward.

Step 9: Insert the magazine spring/lift table into the magazine and then slide the magazine base into the grooves on the bottom of the magazine.

Comment & Rating (12)

@MichaelP

Boosted

Schöne Datei, tolles Druck ergebnis aber leider wieder mal keine Anleitung für den Zusammenbau. Schade 😔 Damit wieder verschwendetes Filament.

The designer has replied

@BrewBoy

I am currently working on them. I'm sorry but I have a busy job

@BrewBoy

there is now a small build guide part of the model page. I hope that helps, it is pretty simple to assemble

@MichaelP

Boosted

Replying to @BrewBoy :

Thank you, that helps me a lot!

@ingo.ralph13

NeinBildfürzusammenbau

The designer has replied

@BrewBoy

I will try to upload some this week.

@user_512152836

do you have a link to any of the springs for the barrel slide?

The designer has replied

@BrewBoy

This is the one I use for most of my projects, but I don't know if the link works outside of North America. 305mm Compression Spring Wire Dia 0.3 0.4 0.5 0.6 0.7 0.8 1 - 5mm Outer Dia 3 3.5 4 4.5 5 5.5 6 7 8 10 12 - 60mm Length 305 mm (aliexpress.com)