★更新日志：2024/5/11

①新增配件——铁氟龙管帽https://makerworld.com/zh/models/457379#profileId-365380

②厚垫片高度调整，减少了因公差导致垫片内厚外薄无法安装的情况

③增加使用蓝丁胶来提升温湿度计密封性的方案

③盖子容量、结构调整。干燥剂容量提升20%！！；开合结构重新设计，牢固不易脱落

PS：前期盖子体积设计比较保守，为了达到更好的干燥体验，现在直接拉到最大值，如发生与较大的料盘卡死的情况，请下载小体积盖子STL文件打印

安装教程：https://www.bilibili.com/video/BV1zM4m1f7Gb/?share_source=copy_web&vd_source=f1eb46ee8050ffda302671e080cf06cc

大家好！这里是晓翼工坊。这款干燥箱采用磁力设计，可以在不开箱的情况下通过外置的磁力钥匙，磁吸旋转轻松回抽耗材，更换耗材更加省时省力。米桶这边我们选择4升体积的，在使用底座而不用悬挂的方案下，可以兼容几乎所有1千克料盘，节约体积减少占地空间。这款米桶的顶盖是可拆卸设计，所以我们可以通过3D打印无损替换，顶盖不用打孔就可以轻松的安装料管与温度计。因为要方便无旋锤打印以及顶盖的开启频率并不高，所以顶盖采用预留凹槽的设计，用剪钳或者镊子撬开的方式开启。温度计也预留了尺寸精准的孔位以便安装。顶盖还设计了一个干燥剂收纳舱，无旋锤支撑打印设计开合丝滑，从此更换干燥剂仅需打开顶盖即可。底座的部分预留了两个孔位用来安装动力杆，垫片薄和厚的摆放顺序是由料盘的宽度决定的，内薄外厚内厚外薄自由调节，窄料盘就先安装薄垫片，宽料盘就先安装厚垫片。垫片带有坡度确保料盘可以及时回正。轴承这里我们使用608ZZ的型号，售价便宜且性能完全足够。中轴安装磁铁的孔位设计了支撑需要用剪钳手动拆除，钥匙部分安装磁铁的时候需要加胶水，安装磁铁也要注意正负极需要一一对应。将中轴安装在料盘中间孔洞内拧上螺母，螺母采用斜面坡度设计可以适配各种直径的料盘。

Hello everyone! This is Victor Studio. This drying Box adopts a magnetic design, which can easily retract consumables by rotating the external magnetic key without opening the box. Replacing consumables is more time-saving and labor-saving. We have chosen a 4-liter box, which can be compatible with almost all 1-kilogram trays without the need for hanging, saving volume and reducing footprint. The top cover of this drying box is designed to be detachable, so we can replace it non-destructive through 3D printing. The top cover can be easily installed with the material tube and thermometer without drilling holes. Because it is convenient to print without a rotary hammer and the opening frequency of the top cover is not high, the top cover adopts a design of reserved grooves, which can be opened by using scissors or tweezers to pry open. The thermometer also reserves precise hole positions for installation. The top cover is also designed with a desiccant storage compartment, and the printing design without rotary hammer support is smooth to open and close. From now on, replacing desiccants only requires opening the top cover. Two holes are reserved in the base for installing the power rod. The order of placement of the thin and thick gaskets is determined by the width of the material tray. The inner thin and outer thick gaskets can be freely adjusted. For narrow material trays, thin gaskets are installed first, while for wide material trays, thick gaskets are installed first. The gasket has a slope to ensure that the material tray can be returned to its correct position in a timely manner. We use the 608ZZ model for bearings here, which is cheap and has sufficient performance. The hole design for installing the magnet on the central axis requires manual removal with scissors for support. When installing the magnet on the key section, glue needs to be added, and the positive and negative poles need to be matched one by one when installing the magnet. Install the central shaft in the middle hole of the material tray and tighten the nut. The nut adopts a sloping design to adapt to various diameters of material trays.

Bom表

箱体： 4L米桶*1
中轴 ：15x5磁铁 *3
钥匙 ：15x5磁铁 *3（多箱体只需一个）
盖子 ：气动接头PC4-M6 *1

湿度计：方形湿度计

底座：608ZZ轴承*4

Box ：4L drying box * 1
Mid axis ：15x5 magnet * 3
Key：15x5 magnet * 3 (multiple boxes only require one)
Cover：pneumatic joint PC4-M6 * 1

Hygrometer：Square hygrometer

Base：608ZZ bearing * 4