v2 GYROID Pattern Reusable Spool (stronger) - Bambu Lab Refill Compatible - Filament Saver Remixed by Gyroid

Remixed by

Gyroid

3D Printer>3D Printer Accessories

Print Profile(3)

All

X1 Carbon

P1S

P1P

X1E

Designers Profile (keep settings as is)

Designer

4.3 h

3 plates

5.0(71)

PETG 0.2mm layer, 2 walls, 15% infill

5 h

3 plates

4.9(7)

ASA - 0.28mm layer, 2 walls, 15% infill

4.3 h

3 plates

5.0(1)

Boost

126

221

419

858

Released

Description

This model is v2 of this spool. The original works great but some people need a stronger spool, so v2 does the trick without using much more filament!

---

Calling all gyroid bros who want a stronger reusable spool!

Gyroid infill is all the rage. It's the strongest and coolest infill style, so why not have it on display while your filament spools rotate?

Well now you can!

Introducing my Bambu Lab Reusable Spool (v2) remix with visible gyroid pattern. This fully supports all Bambu Lab refills.

This remix is based off the official Bambu Lab reusable spool model, so it functions exactly like the official spool, except has the added benefit of a very cool gyroid pattern holding it all together! It also uses less filament.

Not enough gyroid for you? Well guess what? The infill of the solid parts is also gyroid! An absolute must for all gyroid fanboys (and girls) to show off your obsession.

Can I change any settings?

I would strongly advise you to NOT change any settings or modifiers in the print profile. I've spent a lot of time getting the right balance of strength and coolness, so each setting is there for a reason. The only settings you can change are filament settings if you want to print in something other than PLA.

What's the best filament to print this in?

PLA, PLA+, PLA Tough etc. are my favs here. To preserve the strength, it must print well and these print the best without missing a beat. If you dry a lot of filament, print them in PETG or ABS to avoid warping in filament dryers. Do not put this in a filament dryer if you printed using PLA or PLA variants!

When I attach the spools, I can hear clicking. Should I be worried?

No, this is normal! The RFID tag may gently scrape against the gyroid pattern when closing the spool. Just keep going until it clicks in place.

Will this block my RFID readability?

Nope! Your AMS will read the tags fine with this reusable spool.

Do I need to use the spacing shim?

It's been added as a 3rd plate because the official Bambu Lab version uses it. I have never need it personally so I don't bother, but you can use it if you like.

Please let me know what you think and let's see some photos showing off your super cool gyroid pattern spools!

Comment & Rating (85)

@eMeR

Print Profile

PETG 0.2mm layer, 2 walls, 15% infill

Nice spool for cardboard replacement. Fits nicely in AMS. A bit soft if want to put into vacuum bag.

The designer has replied

@253Bigfoot

The PETG definitely gives them some flex

(Edited)

@eMeR

p.s. works perfectly in combination with the spacer to fill the gap of a narrower cardboard spools (like eSUN ePLA Matte): https://makerworld.com/en/models/19445#profileId-18177

@LJNZ

Print Profile

PETG 0.2mm layer, 2 walls, 15% infill

came out perfect! printed in petg

The designer has replied

@253Bigfoot

thanks for the share, the transparent looks great

@myzhar

Print Profile

Designers Profile (keep settings as is)

Great job. More robust than v1 which was already an awesome design

@Bergmanndw

Print Profile

Designers Profile (keep settings as is)

Spool does the job. If you use a dryer make sure you use higher temperature filament. I tried PLA, which warped. I then switched to ABS.

@edakaplan

Print Profile

Designers Profile (keep settings as is)

V2 is better

@ragin666

Print Profile

Designers Profile (keep settings as is)

very cool design!

@kstudioca

Print Profile

Designers Profile (keep settings as is)

Great spool, will print many of these in the future.

@AppleFoot

Boosted

Print Profile

Designers Profile (keep settings as is)

Great! Just sent you a Boost!

(Edited)

@laureddd

Print Profile

Designers Profile (keep settings as is)

Perfect, I tried many but this model is really bery nice. Thanks a lot!

@luftschildkroet

Print Profile

Designers Profile (keep settings as is)

Worked perfect. I used all Bambu Basic PLA -Yellow -Silver -Gray -Black You need to make sure your print-bed adhesion is on point! On my first print the corners warped and the final layer was messed up. Secon print i used 3DLac for better adhesion and a brim of 5mm. Maybe turn top layer speeds a little down (i didn’t) to reduce the streaks.