Filament Vacuum Bag Dyson Adaptor
Copyright Claim
Filament Vacuum Bag Dyson Adaptor
Boost
113
256
54
GIF
Print Profile(1)
0.2mm layer, 2 walls, 15% infill
Designer
1.9 h
1 plate
Boost
113
256
54
0
378
232
Released
Description
UPDATE: Check out my updated V2 here: https://makerworld.com/en/models/189462#profileId-208932
This little Dyson attachment can be inserted in to the seal of a filament vacuum dry bag and suction all the air out in a second or two!
This is a way better option than the little hand pump that comes with the popular AliExpress/Temu/Amazon filament vacuum bags.
Designed for my V8 and believe it fits all V models from V7 onwards? (V6 and older had a different connector design). Let me know in the comments which models it fits.
Comment & Rating (54)
All
Print Profile
0.2mm layer, 2 walls, 15% infill
Useful thing.
The designer has replied
0
Reply
You should check out my updated version. quite a few improvements. link in the description.
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Works well. Fit a bit snug. First time remove was hard. But now it’s okay!
The designer has replied
0
Reply
Hi, I've published a V2 that has a slimmer oval nozzle and pressure relief port that let the Dyson run at max without pulsing. https://makerworld.com/models/189462
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
printed very well but it leaks where it seals around the vacuum so it does not get all the air out. If allowed I may remix so that the small end is more of an oval shape just to make it easier to get out of the bag faster when vacuumed and add a TPU seal so it has more suction
(Edited)
The designer has replied
0
Reply
Hi, I've published a V2 that has a slimmer oval nozzle and pressure relief poort that let the Dyson run at max without pulsing. https://makerworld.com/models/189462
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
printed out perfectly unfortunately it doesn’t fit my Dyson animal.
(Edited)
The designer has replied
0
Reply
I designed it around my V8 and it works on a friend's V11 Animal. It looks like the V series from V7 onwards all have the same attachments. Yours is V6 right? It looks like Dyson had a different attachment on V6 and older. I'll update the model description to alert others. Thanks for the heads up.
(Edited)1
Reply
Can it be used on any model of Dyson vacuum cleaner?
The designer has replied
0
Reply
I've only tested it on my V6 stick and a friend's V12. Looking a product photos it looks like it fits from V7 up to V15 stick vacs, Not sure about the latest Gen5.
0
Reply
Replying to @charlie.waterwo
Thank you. Your design has been of great help to me！
0
Reply
Replying to @LIPENGYI
Sorry, I made a typo, I tested in on my V8. It doesn't look like it fits the V6. Just V7 onwards.
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
If the nozzle was smaller it would be great.
The designer has replied
0
Reply
Yeah, it's a bit of a trade off between air flow and ease of use. I did experiment with smaller nozzle sizes and when you go smaller it puts a lot more strain on the Dyson and takes longer to pull vacuum in the bag, but a little easier to quickly seal the bag when extracting. The size I used is the best middle ground.
(Edited)0
Reply
Hi, I've published a V2 that has a slimmer oval nozzle and pressure relief port that let the Dyson run at max without pulsing. https://makerworld.com/models/189462
0
Reply
Hi, I've published a V2 that has a slimmer oval nozzle and pressure relief port that let the Dyson run at max without pulsing. https://makerworld.com/models/189462
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
fit my V8 Animal, It stuttered a little but it went away, make sure your filter is clean if it keeps doing it.
Printed on sport without issue.
the supports shouldve been unnecessary if the inside geometry was the same as the outside rather than a cylinder inside but its no big deal.
The designer has replied
1
Reply
Hi, I've published a V2 that has a slimmer oval nozzle and pressure relief port that let the Dyson run at max without pulsing. https://makerworld.com/models/189462
0
Reply
is it possible to use air valve with vacuum cleaner?
The designer has replied
0
Reply
My first version of this had the same shape end as the hand pump that comes with the bags. The Dyson doesn't have enough suction power to pull air out through the valves so switch the the dozzle through the seal design currently used.
0
Reply
does not fit newer Dyson models
The designer has replied
0
Reply
Which model Dyson? I don't have access to all Dyson models but if you let me know the models it's not compatible with ill update the description so others are aware.
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Amazing fit and finish! Fits super snug to the Dyson vacuum and helps a lot with ensuring there's little to no air in a zip lock bag!
0
Reply
License
This work is licensed under a
Creative Commons Attribution-Noncommercial-NoDerivatives
© 2024 MakerWorld