Ratchet Fidget by mounty

mounty

Toys & Games>Other Toys & Games

Print Profile(5)

All

P1S

P1P

X1 Carbon

X1E

A1 mini

V2 longlife | 0.2mm layer, 2 walls, 15% infill

Designer

27 min

1 plate

5.0(1)

V1 | 0.2mm layer, 2 walls, 15% infill

Designer

25 min

1 plate

4.8(126)

V1 set of 3 | 0.2mm layer, 2 walls, 15% infill

Designer

1 h

1 plate

4.7(10)

V1 for A1 | 0.2mm layer, 2 walls, 15% infill

Designer

29 min

1 plate

4.9(51)

Click to see more

Boost

282

513

243

1.1 k

1.8 k

Released

Description

NEW

funny clicky fidget ratchet with knurled knob on the one side and hex nut on the other.

basic filamen- (instead of matt) providing better click and longer life due to less wear over time.

carefully brake free the lever from the surface bevor assembly!

new longlife version:

double-spring ensures long life
open heart - better sound

______________________________________________________________________________________________________

single lever provide more precise and predictable click
the spring-loaded lever on rotor allows more tention but also more spring travel = results in better sound and less wear over time
shaft guide compensate the tilt resulting from single lever
no supports needed

origin:

Comment & Rating (243)

@comi

Print Profile

V1 | 0.2mm layer, 2 walls, 15% infill

Nice print, looking forward to try it out! :-) I have found out that the printed model has a really minor defect when printing the ratchet arm, it prints bridge, that is curved in the air, which the printer cant do… So thats why it is straight line. If it is normal and it is intended, then tell me. But other than than, love it! Thank you for your design :-)

(Edited)

The designer has replied

@mounty

Hi Jakub! Thank you for the reply and your reminder ;) You are absolutely right, I didn't recognized this as a design issue- but it is- no doubt! Nevertheless it has no effect (except esthetic issue) on the model. as you can imagine (I just write it down in case someone will find this usefull for overall understanding) there are two opposite target to get at this point: 1) clearance 2) spring form = curve in the air :) I hoped the first "in the air" layer will have slight contact due to adhesion (perhaps it hat in the first prototyped but then after increasing the gap I didn't mention the moment it turned to the straight line). Perhaps it will also work with less gap but then you have to break the lever free bevor assembly- less plug and play :) I will decently think about it for some time, maybe will come up with an idea. Thank you for reporting mate!

(Edited)

@mockingbirdthew

Replying to @mounty :

might cause some people issues if that first unsupported layer drags around. an easy fix might be to give that 'spring' a slight angle and then it won't extend so far without any support, but it'll decrease the likelihood issues. will also make the spring slightly weaker. but the bigger concept is potential filament drag issues causing problems elsewhere in the print. otherwise, nice! good job. :-)

@Mikeyy88330

Print Profile

V1 for A1 | 0.2mm layer, 2 walls, 15% infill

it’s so fun to play with. the click is very satisfying. I felt the need to make it bigger and I would definitely recommend doing that, the sound difference is amazing.

The designer has replied

@mounty

ahha Mate I never thought about scaling it! Very nice :)) Thanks for sharing

@mzdad

Boosted

Dang, now i need to do that xD good idea!

@user_1481354334

Print Profile

V1 | 0.2mm layer, 2 walls, 15% infill

very satisfying click

The designer has replied

@mounty

hi! thank you for sharing pictures? I love the color? What is it? Is it a Bambu filament?

@user_1481354334

yep its a red PETG bambu filament

(Edited)

@Stevetalkowski

Print Profile

V1 | 0.2mm layer, 2 walls, 15% infill

Really amazing at how fine the resolution is on the A1. Printed two of these for nice color combo with Bambu PLA.

The designer has replied

@mounty

Bambu did a great job! only that makes such stuff possible. turned out great! thanks for sharing pictures mate!

@biggusdickus

Print Profile

V1 | 0.2mm layer, 2 walls, 15% infill

printed beautifully with Inland gold Silk PLA!!

The designer has replied

@mounty

😍thank you for the pic, looking great!

(Edited)

@adrian_ApeX

Print Profile

V1 for A1 | 0.2mm layer, 2 walls, 15% infill

tuned out great, printed it with pla basic and has no issues. used my new p1s with top off and door open on sport setting nothing changed

The designer has replied

@mounty

thank you for the pics! 🫡

@FilliFuu

Print Profile

V1 | 0.2mm layer, 2 walls, 15% infill

huge improvement over the original, thanks.

The designer has replied

@mounty

Thank you! :)

@bradaline

Print Profile

V1 | 0.2mm layer, 2 walls, 15% infill

cool

The designer has replied

@mounty

looking great! thanks for sharing!

@ikkon

Print Profile

V1 for A1 | 0.2mm layer, 2 walls, 15% infill

Printed great with a satisfying sound

The designer has replied

@mounty

Thank you for sharing pictures! Looking great 👍

@GenghisKhan39

Print Profile

V1 | 0.2mm layer, 2 walls, 15% infill

Nephews like these, but I might like them more lol. Printed on A1 at default settings in Bambu Orange PLA, Bambu Grass Green Matte PLA, and Overture Space Gray + Blue PLA. Really nice when you mix and match the colors. Thanks for these!

The designer has replied

@mounty

thank you for positive feedback :) and also for sharing pictures :) I like you enjoying it!

License

This work is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.