Power cable guide for BentoBox Shared by Addamas

Rob the 3D Printing Dad

Shared by

3D Printer>3D Printer Accessories

Print Profile(2)

All

P1P

P1S

X1 Carbon

X1E

10mm Brim | 0.2mm layer, 2 walls, 15% infill

29 min

1 plate

5.0(8)

Original 0.2mm layer, 2 walls, 15% infill

24 min

1 plate

4.6(8)

Boost

Released

Description

I am sharing on Makerworld this awesome project made - not by me - but Printables user Rob the 3D Printing Dad

This part is used to hide cables powering BentoBox inside Bambu printers.

Sharing his tip:
Use a small piece of double sided tape to fix the left side.
It might be to long, just snip a bit of the end of it is.

All rights comes to his work. I only reshared and added additional profile with 10 mm brims.

Original: https://www.printables.com/pl/model/469451-power-cable-guide-for-bentobox

Comment & Rating (21)

@Bambzle

Print Profile

Original 0.2mm layer, 2 walls, 15% infill

printed nicely. love that is has snap in parts to hold most of it down. definitely did need to cut about 2mm from the left side

@rdc.arch

Print Profile

10mm Brim | 0.2mm layer, 2 walls, 15% infill

printed without issue in Bambu PETG. I would have preferred it at correct length instead of requiring timing. That said, when I put enough light in to trim, I found plenty of other through holes to choose from, including one right next to the BentoBox, so I didn't use the print in the end. I might make a cover for this location if seeing the wires bothers me enough.

@Qjeezy

Print Profile

10mm Brim | 0.2mm layer, 2 walls, 15% infill

printed great! I did have to clip the end a little bit for it to fit as stated in the description. snaps in place nice and firmly.

The designer has replied

@Addamas

Thank you, I appreciate feedback! Happy printing!

@Rockygo46

Hi, thanks for sharing, I wanted to know which double-sided adhesive should I use exactly? can you tell me please thanks!

The designer has replied

@Addamas

I have not yet found reliable tape, it must survive up to 60°C. Classic tape for decoupage is not a good choise as it de-glue at higher temps so I have to press it again when cool down. 3M tapes might be good or something for outside.

@Rockygo46

Replying to @Addamas :

Thanks, yes probably something from 3M should be reliable for both cases (temperature resistance and tenacity) best regards

@crowellsr_eng

Print Profile

10mm Brim | 0.2mm layer, 2 walls, 15% infill

Had a bit of brim come off the plate but the part held on and finished

@dleone617

Print Profile

Original 0.2mm layer, 2 walls, 15% infill

Printed just great. Had to snip off a little, to get it to lay flat, but no big deal!

@tm8vcd88rv

Print Profile

Original 0.2mm layer, 2 walls, 15% infill

I printed it in PLA and so far it’s working great and looks so much nicer than bare wires lol

@eduardogodoypla

Print Profile

Original 0.2mm layer, 2 walls, 15% infill

printed well! easy print!

@MrDulkes

Print Profile

Original 0.2mm layer, 2 walls, 15% infill

Other Issues:Slightly too long. I cut some off and that made it perfect. Printed with ABS to make sure it could handle chamber temps

The designer has replied

@Addamas

Issue is written in model info as it’s inherited from original creator. I wanted to keep as vanilla to original creator as possible and everybody cuts for their needs.