Quoridor (Maze Board Game)

Remixed by
Copyright Claim

Quoridor (Maze Board Game)

Remixed by
Boost
122
258
66

Print Profile(2)

All
P1S
P1P
X1
X1 Carbon
X1E
A1
A1 mini

0.2mm layer, 2 walls, 15% infill
0.2mm layer, 2 walls, 15% infill
Designer
8.2 h
3 plates
5.0(41)

72% Scaled for Mini, 0.2mm layer, 2 walls, 15% infill
72% Scaled for Mini, 0.2mm layer, 2 walls, 15% infill
8.2 h
3 plates
1.0(1)

Boost
122
258
66
4
218
543
Released

Description

The English translation is below.

 

Dies ist ein Remix von dem bekannten Spiel Quoridor.

 

Spieleranzahl: 2 – 4
Ziel: Mit seiner eigenen Figur die gegenüberliegende Seite des Spielbrettes als Erster zu erreichen
Vorbereitung: Die 20 Wände werden gerecht zwischen den Spielern aufgeteilt.

 

  • Das Spiel beginnt in der ersten Reihe in der Mitte (bei zwei Spielern ist es mit dem Plus gekennzeichnet.)
  • Der Spieler bewegt entweder seine Figur oder stellt eine Wand auf. Beides ist in einem Zug nicht möglich.
  • Auf der Plattform platzierte Wände müssen an 4 Felder angrenzen und können nicht mehr verschoben werden.
  • Es wird reihum gespielt, dabei darf die Figur (sofern der Weg nicht blockiert ist) in alle vier Himmelsrichtungen bewegt werden.
  • Wenn sich zwei Spielfiguren gegenüberstehen kann der Spieler, der am Zug ist, über die gegnerische Spielfigur springen. Wenn das Feld hinter der übersprungenen Figur durch eine Wand oder eine weitere Figur blockiert ist, darf ein freies Feld links oder rechts von der übersprungenen Figur gewählt werden.
  • Die Wände müssen so platziert werden, dass alle Spieler noch die Möglichkeit haben, ihre Zielseite zu erreichen.
  • Wenn der Spieler keine Wände mehr hat, muss er mit seiner Figur einen Zug machen. Deshalb sollten die Wände sinnvoll eingesetzt werden, weil sie gegen Ende des Spiels eine sehr entscheidende Rolle spielen können.
  • Der erste Spieler, der eines der 9 Felder in der letzten Reihe der Spielplattform erreicht, gewinnt das Spiel.

Storage box for Quoridor von Crunchy

https://makerworld.com/en/models/142419#profileId-155060

 

---------------------------------------

 

Google translation:

This is a remix of the famous game Quoridor.

 

Number of players: 2 – 4
Goal: To be the first to reach the opposite side of the game board with your own figure
Preparation: The 20 walls are divided equally between the players.

 

  • The game begins in the front row in the middle (if there are two players, it is marked with a plus.)
  • The player either moves their figure or puts up a wall. Both are not possible in one go.
  • Walls placed on the platform must be adjacent to 4 spaces and can no longer be moved.
  • It is played in turns and the figure can be moved in all four directions (as long as the path is not blocked).
  • When two pieces face each other, the player whose turn it is can jump over the opposing piece. If the space behind the skipped piece is blocked by a wall or another piece, you may choose a free space to the left or right of the skipped piece.
  • The walls must be placed so that all players still have the opportunity to reach their target side.
  • When the player runs out of walls, he must make a move with his figure. That's why the walls should be used wisely because they can play a very crucial role towards the end of the game.
  • The first player to reach one of the 9 spaces in the last row of the playing platform wins the game.

Storage box for Quoridor by Crunchy

https://makerworld.com/en/models/142419#profileId-155060

Comment & Rating (66)

Please fill in your opinion
(0/5000)

I absolutely love this print, it turned out amazing! Great design OP and the aesthetic is very on point for the game! I created a box for the game pieces though as I wanted a better way to transport them without losing any. I linked it here if anyone else wants to print it. https://makerworld.com/en/models/410781#profileId-312746
The designer has replied
0
Reply
I'm glad you like the game so much and thank you for your game box. It looks good. I'll definitely print it.
0
Reply
Is it possible to get a V2 with magnets so it will close without dropping everything?
0
Reply
Replying to @marioandres.mar :
The box is friction fit and the tolerances are tight enough on it that once it’s shut it will not open by itself. A magnetic case wouldn’t work it you dropped it though. It would easily open as the small magnets aren’t strong enough to hold it shut in an impact.
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Printed it 72% scale for mini and turned out awesome still! Great design love this game.
The designer has replied
1
Reply
great idea. feel free to post it as a profile.
(Edited)
1
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
printed great and is a fun little game
The designer has replied
0
Reply
thank you, have fun with it
0
Reply
Replying to @PrintGeggo :
I played with my 4 year old. absolutely demolished her.
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Came out beautiful. I used Color changing rock filament for the stones and it looks amazing with these broken patterns.
The designer has replied
1
Reply
Thank you for your pictures and your review. I like your choice of colors 👍
(Edited)
1
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Super cool! Can't wait to play!
The designer has replied
1
Reply
Thank you for your review and your picture. Have fun with the game. A new game from me will be coming out soon.
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
prints perfectly. just added some brims to the walls.
The designer has replied
0
Reply
Thanks for the review. I tested it several times with and without brims. The brims weren't necessary in my test. And when I printed with brims, they couldn't be removed cleanly.
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
love this game
The designer has replied
0
Reply
thank you, that makes me happy
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Funny game!
The designer has replied
0
Reply
Thanks for the picture and the review
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
works perfect and is really fun to play ;) only thing that I have to find now is a case that fits 😅Thank you!
The designer has replied
0
Reply
thank you for your picture and review. I would like to create a case for the figures and boards.
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Pefect print and now a full evening of playing.
0
Reply