AMS Lid Riser for Bambu Lab AMS
Copyright Claim
AMS Lid Riser for Bambu Lab AMS
Boost
476
1011
856
Print Profile(8)
v2 Left-hand side - 0.2mm layer, 2 walls, 15% infill
Designer
1.1 h
1 plate
v2 Right-hand side - 0.2mm layer, 2 walls, 15% infill
Designer
1.1 h
1 plate
v1 Both sides - 0.2mm layer, 2 walls, 15% infill
Designer
1.4 h
1 plate
PETG 0.24mm layer, 2 walls, 15% infill
1.5 h
1 plate
Click to see more
Boost
476
1011
856
8
2.5 k
2.3 k
Released
Description
Version 2 is now available! Please use the v2 Left-hand side and v2 Right-hand side print profiles and read the instructions below!
DISCLAIMER: Print profiles NOT created by DesignCraft may contain outdated model versions or suboptimal slicer settings. Use at your own risk! I have no control to moderate or remove these third party print profiles.
Description:
The AMS Lid Riser allows you to keep your AMS lid closed while providing additional clearance for larger filament spools.
Need even more spool clearance? The AMS Lid Riser XL is now available!
Version 2 Instructions:
- Print both sides of the AMS Lid Riser v2 along with the tongues for each side.
- Insert the tongues into the bottom of each side. Press each side firmly down on a flat surface (such as a table) to make sure the tongue is fully inserted and even. While glue is not required I did apply CA glue to the tongues before assembly. Please make sure you're applying glue to the correct side as it only fits in one way.
- Wait for the glue to dry before installing the AMS Lid Riser v2.
- To install the AMS Lid Riser v2 open the AMS lid, insert one riser piece at a time and firmly press the tongue into the rubber gasket, and close the AMS lid as pictured.
Version 1 Instructions:
- Print both sides of the AMS Lid Riser v1
- It's recommended that you print this model with a brim on a cool, smooth surface build plate.
- Once printing is complete, open the AMS lid, insert one riser piece at a time, and close the AMS lid as pictured.
- The AMS Lid Riser has a tongue on the bottom that fits into the AMS lid groove. The AMS lid tongue closes into the top groove of the AMS Lid Riser.
Notes:
- Do not enable Flow Dynamics Calibration when printing or the part may overlap the lines.
- It is not recommend to re-orient the position of the parts on the build plate unless you're an advanced user. They're positioned in this fashion to avoid warping that can be caused by close proximity to the fan.
- Shown as printed in standard PLA
Comment & Rating (856)
All
Print Profile
v1 Both sides - 0.2mm layer, 2 walls, 15% infill
Ist top luft dicht bis hinten 👌
The designer has replied
1
Reply
Looks great! Thank you for rating!
0
Reply
Hallo Robert, hast du eine modifizierte Variante oder wieso ist bei dir hinten keine Lücke?
(Edited)0
Reply
Replying to @AU3D
Würde mich auch interessieren. Bei dem Make darüber ist deutlich eine Lücke sichtbar.
(Edited)0
Reply
Print Profile
v1 Both sides - 0.2mm layer, 2 walls, 15% infill
Printed great- air tight! made with Jessie glitter black PLA.
The designer has replied
1
Reply
Awesome! Thanks for the rating and make!
(Edited)1
Reply
Airtight? You don't have a gap at the back on b oth sides?
0
Reply
Replying to @AU3D
everyone who has printed this has a small gap at the back on both sides, does the job tho
0
Reply
Print Profile
v1 Both sides - 0.2mm layer, 2 walls, 15% infill
perfect for what i need awrsone design
(Edited)
The designer has replied
1
Reply
Thank you for rating!
0
Reply
Replying to @DesignCraft
can you add the ipt models, im using printalot spools and it need to increse the height a litle bit like 5mm more, it work but when the spool start to loose weight it start to stop.
so incresing the space over the spool should fix this.
Printalot uses 208mm spools
(Edited)0
Reply
Replying to @danimar.gabriel
Thank you for the feedback! I've created a new model, the AMS Lid Riser XL, which provides additional clearance. You can find it on my profile or directly here: https://makerworld.com/en/models/244691
0
Reply
Boosted
Thank you, great print and design to raise mu AMS to hold larger spools
(Edited)
The designer has replied
2
Reply
Thank you for sharing your make!
0
Reply
Print Profile
v1 Both sides - 0.2mm layer, 2 walls, 15% infill
Works! Thank you 🙂
The designer has replied
2
Reply
Thank you for rating and sharing all these great pics!
0
Reply
Print Profile
v1 Both sides - 0.2mm layer, 2 walls, 15% infill
top
The designer has replied
1
Reply
Nice! Thank you for sharing your make and rating!
(Edited)1
Reply
it's perfect for my filalab-spools, which are about 5mm to big for the ams 👌
(Edited)1
Reply
Print Profile
v1 Both sides - 0.2mm layer, 2 walls, 15% infill
Easy print. Used Sunlu APLA Grey which is not very shiny
The designer has replied
1
Reply
Thank you for sharing your make and rating!
0
Reply
Boosted
Print Profile
v2 Left-hand side - 0.2mm layer, 2 walls, 15% infill
now my 3D Fuel spools fit perfectly!
(Edited)
The designer has replied
1
Reply
Thank you for sharing your make and rating!
0
Reply
Print Profile
v1 Both sides - 0.2mm layer, 2 walls, 15% infill
Nice, thank you!
The designer has replied
1
Reply
Thank you for sharing your make and rating!
0
Reply
Print Profile
v2 Left-hand side - 0.2mm layer, 2 walls, 15% infill
Looks great, I used PolyTerra Wood Brown PLA for a more serious look
The designer has replied
1
Reply
Looks seriously good! Thank you for rating!
0
Reply
License
This work is licensed under a Standard Digital File License.
You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.
Related Models
© 2024 MakerWorld