Apple Watch charger stand base - Easy to remove the charging cable!
Copyright Claim
Apple Watch charger stand base - Easy to remove the charging cable!
Boost
13
37
25
Print Profile(2)
TOTAL V3; 0.2mm layer, 4 walls, 15% infill
Designer
1 h
1 plate
TOTAL V2; 0.2mm layer, 4 walls, 15% infill
Designer
1.1 h
1 plate
Boost
13
37
25
1
113
142
Released
Description
Introducing the ultimate Apple Watch charger base or stand!
Easy to print without any support. It uses you standard Apple Watch and Apple Watch Ultra charging cable with MagSafe (USB-C only). This design makes it easy to attach the cable, but also easy to remove. Just press the hole in the back and the MagSafe charger pops out. Super convenient when traveling, as you don't need to carry around the charging base.
NOTE
There are four versions available:
- Total v2; Prints in 1 piece and this works for most printers and filaments. The MagSafe charger fits just snug in the base.
- Total v3; Prints in 1 piece and this works for printers and filaments where the MagSafe charger is a little loose. Added some nudges.
- 3 parts v2; Needs to be glued and this works for most printers and filaments. The MagSafe charger fits just snug in the base.
- 3 parts v3; Needs to be glued and this works for printers and filaments where the MagSafe charger is a little loose. Added some nudges.
I would start with v2 and if that's a little loose, try v3. Prints totally fine in 1 piece without support on my X1C. It prints a little bit nicer in the 3 parts, but you could see more glue lines. I had the best result on a Cool Plate with Bambu PLA.
Happy printing!
Comment & Rating (25)
All
Print Profile
TOTAL V3; 0.2mm layer, 4 walls, 15% infill
oggetto fatto bene, utile e comodo da usare.
The designer has replied
1
Reply
Very nice! Thank you for sharing!
0
Reply
Boosted
Print Profile
TOTAL V3; 0.2mm layer, 4 walls, 15% infill
(Edited)
1
Reply
Print Profile
TOTAL V3; 0.2mm layer, 4 walls, 15% infill
The designer has replied
1
Reply
Hi, thank you for the review. Do you have any feedback that I can use to make sure the profile/design gets more than 3 stars next time? Happy to help!
0
Reply
Replying to @NoNameToo
The model itself is well designed but the print profile was not optimized for overhang quality and I had to print multiple times to get the charger to fit correctly.
(Edited)1
Reply
Replying to @Osprey
Thanks for the feedback. That's something I can work with. I printed it with various filaments and did not have an overhang issue. But I will tweak the profile to handle overhangs better. Thanks Again!
0
Reply
Print Profile
TOTAL V2; 0.2mm layer, 4 walls, 15% infill
Habe es gedruckt ohne die Beschreibung zu lesen ;) es gibt zwei verschiedene größen des alten Apple watch ladekabels, von der apple watch series 1 und 2 funktioniert auch das normale usb ladekabel
Beim Ladekabel der series 6 ist der usb stecker zu groß, wenn man allerdings auf 120% scaled funktioniert auch das! Sprich nicht nur für usb c verwendbar
1
Reply
Print Profile
TOTAL V3; 0.2mm layer, 4 walls, 15% infill
Some overhang problem at the top but overall usable and pretty.
0
Reply
Print Profile
TOTAL V3; 0.2mm layer, 4 walls, 15% infill
1
Reply
Print Profile
TOTAL V3; 0.2mm layer, 4 walls, 15% infill
1
Reply
Print Profile
TOTAL V3; 0.2mm layer, 4 walls, 15% infill
1
Reply
Print Profile
TOTAL V3; 0.2mm layer, 4 walls, 15% infill
1
Reply
Print Profile
TOTAL V3; 0.2mm layer, 4 walls, 15% infill
1
Reply
License
This work is licensed under a
Creative Commons Attribution-Noncommercial-Share Alike
© 2024 MakerWorld