Airless Ping Pong no break Ball! Table Tennis by filete3d

filete3d

Hobby & DIY>Sport & Outdoors

Print Profile(3)

All

A1 mini

P1S

P1P

X1 Carbon

X1E

0.2mm layer, 2 walls, 15% infill

Designer

50 min

1 plate

4.9(55)

0.2mm layer, 2 walls, 15% infill

Designer

1 h

1 plate

4.3(7)

0.2mm layer, 2 walls,15% gyroid infill

50 min

1 plate

Boost

117

134

583

427

Released

Description

Airless Ping Pong Ball, reinforced circle mesh!

Tested in basic PLA its approved to regular playing without major smashing, in wich case resistance is improved with PETG (or any other material with better layer adhesion or higher melting temperature such as ABS or Nylon)

Improved resistance, bouncing and weight approach

After some tests with hex meshes, we conclude that the circle mesh has greater resistance by better distributing the hitting response on the surface, this means that less plastic can be used to make the ball and in this way achieve a better weight match with the real ball.

Improved bounciness consistency

The circle mesh allows a better surface finish in the lower and upper critical areas of the print, this makes the direction of the bounces more regular. With a slight sanding in the support sector, a smooth surface is achieved throughout the geometry.

The print profiles already come with pre-loaded supports, make sure to view them correctly before printing, once printing is finished, wait a few minutes for the plate to cool to avoid deformations in the sphere.

Check my current state on airless balls:

Airless Tennis Ball v2.0 https://makerworld.com/en/models/253687#profileId-270125

Airless Baseball Wiffle Softball Ball v2.0: https://makerworld.com/en/models/227359#profileId-244997

Airless Basket , Soccer, Voley or Handball Ball v1.2: https://makerworld.com/en/models/223189#profileId-241192

Airless Golf Ball: https://makerworld.com/en/models/383904#profileId-284030

Comment & Rating (72)

@Fin3dPrinting

Print Profile

0.2mm layer, 2 walls, 15% infill

amazing came off the build plat I bounced it and I was amazed how ell it bounced! I threw at the wall after a little and it broke 😭😭amazing model overall!! printed in PETG

(Edited)

@user_3460996239

can you please explain me how to make those supports as they are in the photo, I am new to this and I have not been able to understand how to make them to be able to print this type of products, thanks for your help.

@user_3460996239

Replying to @user_3460996239 :

i use orca slider

@Fin3dPrinting

all I did was use the existing print profile with Bambu studio. I would recommend Bambu studio. if you need any more help let me know!

(Edited)

@marieclaire.cil

i made a 200% version on my A1 mini and it still has boun

The designer has replied

@filete3d

awesome! gonna try it too

@Bibo5175

Print Profile

0.2mm layer, 2 walls, 15% infill

printed out perfectly, the supports came off very easy, it bounces great on a paddle, it is decently strong in PLA but a stronger material would be better

The designer has replied

@filete3d

thank you!, for casual playing with no smashing it will be fine, i still have the one that i printed the first with no cracks!

@evilinheaven

Print Profile

0.2mm layer, 2 walls, 15% infill

Petg version is not round. May add difficulty to the match.

The designer has replied

@filete3d

hi there! they are the same file with different Profiles, it seems to be a deformation due to the print, for troubleshooting i recommend to be sure to remove the print only after the bed cooled down enough and reduce printing speed so the layers get time to cool and the filament get correctly placed over the first layers. If you try to print it again please tell me if something of this solved the problem!

(Edited)