Pastamatic - Screwable Pins
Copyright Claim
Pastamatic - Screwable Pins
Boost
17
40
21
Print Profile(1)
0.2mm layer, 2 walls, 15% infill
Designer
1.2 h
1 plate
Boost
17
40
21
0
99
47
Released
Description
I Created this Pins for more stability at the fantastic Pastamatic.
There are three Versions for the Pins. If u look on the Screenshot → On the original Pastamtic u have to use the Pins in the middle and the right side. Delete the four long pins on the Top. If u use my Motormount → Delete the right one and use that four on the Top instead.
12mm wrench recommended
The Screws i took:
- Short Pins M4x10
- Long Pins M4x16
- MotorMount Pins M4x16 or M4x20
Important! Screw it down with less strength! U have to check that the Gears are turning free…!
Here are my other Pastamatic Add on`s:
Enjoy, have Fun and Visit or Follow my Profile for more!
Comment & Rating (21)
All
Print Profile
0.2mm layer, 2 walls, 15% infill
great!
The designer has replied
0
Reply
thx!
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
The screw pins are clearly required when hanging a motor off of the Pastamatic. That said I also used a few of the screw pins in other locations where swing clips were not utilized to hold the spindles in place.
(Edited)
The designer has replied
0
Reply
Also here, thanks for your comment... Have a nice Time!
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
There would have to be a tool to counter, I held them with a pair of pliers, that goes, but leaves marks.
Es müsste ein Werkzeug zum kontern geben, habe sie mit einer Zange gehalten, das geht, hinterlässt aber marken
edit: es sah für mich nicht so aus, als ob ein maulschlüssel passt, hätte man auch selber mal testen können :)
(Edited)The designer has replied
0
Reply
in der Tat gibt es ein passendes Werkzeug 😉. Danke für den Hinweis, das werde ich in der Beschreibung ergänzen. In sofern wäre eine Anpassung deiner Bewertung sehr nett…
0
Reply
shit happens… 😜Ja, ist aufgrund der Form nicht ganz eindeutig. Danke dir fürs anpassen!
0
Reply
While it printed perfectly, I'm not exactly sure how this is supposed to be assembled. Not sure if I'm meant to thread directly into the pins or add heat inserts. Maybe some pictures to clarify would help.
The designer has replied
0
Reply
Just screw it together. There is nothing special.
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
grat upgrade
The designer has replied
0
Reply
thx!!!🙏
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Definitely a must if you’re printing the Pastamatic winder. These work exactly as intended. I used M2 bolts, which worked just fine. Well done!
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
super
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Bed Adhesion Issue
The designer has replied
0
Reply
Hallo bendudu, deine betthaftung kannst du mit ganz einfachen Spülmittel unter warmen fließendem Wasser verbessern. also reinigen. Unter Geschwindigkeit kannst du für den First Layer 30mm und 70mm eingeben.
Die Betthaftung hat nichts mit dem Model an sich zu tun. Zumindest nicht in diesem Fall. Es wäre nett wenn du dementsprechend deine Bewertung anpasst. Du kannst mir auch gerne eine PM schreiben wenn du weiterhin Probleme hast.
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
The designer has replied
0
Reply
Hi there… Can u report what’s not good with this?
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
0
Reply
License
This work is licensed under a
Creative Commons Attribution-Noncommercial-Share AlikeRelated Models
© 2024 MakerWorld