Skip to content

FMS ATLAS 6x6 Gooseneck trailer multi lenght and multi ramps

Advertising
Share
Add to
Make
Advertising
?
Creation quality: 5.0/5 (1 vote)
Evaluation of members on the printability, utility, level of detail, etc.
  • 12.7k views
  • 19 likes
  • 46 downloads
  • 2 collections
License
3D design format
STL Folder details Close
  • A frame front gooseneck trailer DEREK atlas.STL
  • A frame rear gooseneck trailer DEREK atlas.STL
  • Inside rim tyres 35 gooseneck.STL
  • ball joint male.STL
  • cale boule 6 gooseneck trailer DEREK atlas.STL
  • center part rim tyres 45 gooseneck.STL
  • demi rotule 5.STL
  • gooseneck trailer L frame 120mm high +10mm high.STL
  • gooseneck trailer L frame 120mm.STL
  • gooseneck trailer L frame 180mm high +10mm high.STL
  • gooseneck trailer L frame 180mm.STL
  • gooseneck trailer L frame extension 120mm .STL
  • gooseneck trailer L frame extension 180mm .STL
  • gooseneck trailer L frame extension 60mm .STL
  • gooseneck trailer L frame extension end cap.STL
  • gooseneck trailer L frame extension end cap.STL
  • gooseneck trailer axle bracket tyres 35 x4.STL
  • gooseneck trailer axle x2.STL
  • gooseneck trailer leaf spring reinforcement plate x4.STL
  • gooseneck trailer leaf spring tyres 35 x2.STL
  • gooseneck trailer leaf spring tyres 45 x2.STL
  • gooseneck trailer middle wood plate ramp x1.STL
  • gooseneck trailer middle wood plate x5.STL
  • gooseneck trailer mobile flat ramp transport position bracket x2.STL
  • gooseneck trailer mobile flat ramp x2.STL
  • gooseneck trailer mobile flip ramp x2.STL
  • gooseneck trailer ramps hinge 3 parts to be glued on the trailer.STL
  • gooseneck trailer rear lights.STL
  • gooseneck trailer rear ramp section to be glued on L frame x2.STL
  • gooseneck trailer side band ramp x2.STL
  • gooseneck trailer side band x10.STL
  • gooseneck trailer side light.STL
  • gooseneck trailer support pipe cap front end.STL
  • gooseneck trailer support pipe fronr end .STL
  • gooseneck trailer upper struct on L frame x5.STL
  • gooseneck trailer upper structure ramp x1.STL
  • goussets x2 gooseneck trailer DEREK atlas.STL
  • junction reinforcement x2 gooseneck trailer DEREK atlas.STL
  • leaf spring fixture tires 45 x4 gooseneck trailer DEREK atlas.STL
  • leaf spring x2 gooseneck trailer DEREK atlas.STL
  • outside rim tyres 35 gooseneck.STL
  • pieds ar x2 gooseneck trailer DEREK atlas.STL
  • pieds av x2 gooseneck trailer DEREK atlas.STL
  • rim gooseneck tyres 45 inside.STL
  • rim gooseneck tyres 45 outside.STL
  • straight frame 180 x4 gooseneck trailer DEREK atlas.STL
  • support pieds D x4 gooseneck trailer DEREK atlas.STL
  • support pieds G x4 gooseneck trailer DEREK atlas.STL

Learn more about the formats
Publication date 2021-05-13 at 21:09
Design number 425980
lulu3Dbuilder

lulu3Dbuilder

3D printer file info

3D model description

Fan of unusual thnigs, this is my version of Gooseneck trailer. Inspired by US manufacturer pictures and drawings we can find on internet. It is actually design to suit the FMS ATLAS 6x6 following Derek request.

The version in pictures is 540mm payload area (flat area) with additional rear ramp. 3 section of 180mm are needed, then I cutted in different pieces with male and female connectors to let you compose your own trailer. You can see in picture the different sections. there are even 10 mm higher L frame versions in case you want to use this trailer on a car with higher bed. Ball joint female is adjustable and the Pipe in which the ball joint is going can easily beeing printed longer with upscale on Z.

two versions of the rear ramps are available,

one is a 180Β° flipable one which let a nice flat effect on the ramp in transport position

one is a flat ramp you can let vertical or even a bit on the rear for transport position. 2 brackets have then to be fitted on the ramps and trailer. Holes are already there, just use M1.4mm screws. One eye of the bracket should be cut with a cutter to get a hook form.

For this version of ramp you need to fit the rear stabs under the main frame. Tight the screws and it will stay in place.

Rampe hinge need a 2mm rod, lenght corresponding to the trailer width, 120mm.Take care when glueing the 3 fix sections on the ramp upper structure. It must be glued with the rod inside all parts to be straight and easily manoeuvrable. No special issue there, just be cautious. Check the flipable ramps are aligned with the trailer in transport position. Key point to have something nice.

Two versions of wheels are available with same payload plate level from the ground.

One for 35mm wheels, with bigger articulation

One for 45mm wheels with more all terrain look.

Either you print the rims included in the files set or you use any wheel you find on toys with 3mm holes in the center.

In cas you use the included rims, I gove you below reference of the tires I used in pictures.

please notice that the 2 brackets on which the leaf springs are articulated (4 half brackets) can slide on the A frame. Normaly if you tighten the screws it stay in place . If not just add a piece of adhesive paper to reduce the gap. It is good to have it sliding to adjust position of the wheels along the frame and then adjust the weight on the ball joint to get full shocks movement. If you don't care, choose the best look position and glue.or screw.

The upper parts are 60mm long, you have one structure part, two side panels and one central panel which try to simulate wood plates. Depending of the lenght you choose you have to print several set of those 4 parts.

When assembling the 2 full L frames please take car to make it straight and equal. General geometry is depending of that glueing. Same when you add the ramp parts at the end of the L frame.

In case you don't want to use the ramp, you have a cap to print and cover the female connector of the L frame.

You have a side light you can duplicate all around and a 3 modules rear lamps, see pictures.

There are reinforcement plates for the leaf springs ends which have to be glued on the leaf springs before assembly on the axle. It prevent of breakage of the leaf spring end area when you tighten the screws.

Flat bed plus ball to allow hauling is in other set of files.

Depending of the holes you will find, you need some M1.4, M2, M2,5 and M3 screws.

Wheels to axle : M3

leafspring to axle : M1.4

Leaf spring brackets assembly : M2

Leaf spring to bracket : M2

end of stab leg : M2.5

Female ball joint adjustment M2.5

flat ramp bracket on ramp and on trailer : M1.4

stab legs on brackets : M2

Rims assembly : M1.4

Tyres 45mm : 13616 Tire For RGT 136240 V2 1/24

Tyres 35mm :Wltoys 1/24 RC ref A242-01

https://www.ebay.fr/itm/4pcs-13616-RC-Car-Tire-For-RGT-136240-V2-1-24-2-4G-Vehicle-RC-Rock-Crawler-Parts/184566408417

https://www.ebay.fr/itm/Wltoys-1-24-RC-Car-A242-Spare-Parts-4Pcs-Tires-A242-01/172428879402?ssPageName=STRK%3AMEBIDX%3AIT

2mm rod: https://www.ebay.fr/itm/2Pcs-Stainless-Steel-Shaft-Round-Rod-300mmx2mm-for-DIY-Toy-RC-Car-Model-Part/392267264913

https://youtu.be/stEkEorkHKg

3D printing settings

Noting special

some parts need supports, set support size to 1.2mm specialy for rims.

Print smal parts, ball joint parts, leaf spring at low speed.

big parts were printed here at 50mm/s on a creality CR10

3D printing settings

40mm/s Infill 30Β§

Tags

Advertising

Page translated by automatic translation. See the original version.
Issue with this design? Report a problem.
Check out similar designs

Would you like to support Cults?

You like Cults and you want to help us continue the adventure independently? Please note that we are a small team of 3 people, therefore it is very simple to support us to maintain the activity and create future developments. Here are 4 solutions accessible to all:

  • ADVERTISING: Disable your banner blocker (AdBlock, …) and click on our banner ads.

  • AFFILIATION: Make your purchases online by clicking on our affiliate links here Amazon.

  • DONATE: If you want, you can make a donation via Ko-Fi πŸ’œ.

  • WORD OF MOUTH: Invite your friends to come, discover the platform and the magnificent 3D files shared by the community!

Sharing and downloading on Cults3D guarantees that designs remain in makers community hands! And not in the hands of the 3D printing or software giants who own the competing platforms and exploit the designs for their own commercial interests.

Cults3D is an independent, self-financed site that is not accountable to any investor or brand. Almost all of the site's revenues are paid back to the platform's makers. The content published on the site serves only the interests of its authors and not those of 3D printer brands who also wish to control the 3D modeling market.
Currency: USD
Cults.
100% secure payment by credit card, PayPal, Apple Pay, Google Pay, etc.
View all payment options.