Ray Gun from Black Ops UNDER RECONSTRUCTION

Prints (-1)

Description

SummaryRay Gun from Nazi Zombies in Call of Duty: Black Ops. Now ready to accept electronics to become a fully functional prop! I used some blueprints that I found online to scale the model. It feels quite comfortable in the hand. Supplies: Epoxy Two small magnets Some wire Clamps or some weights (cans of soda work too) Wax paper Flat surface Hardware: 4x M3x10mm Socket Head Cap Screws 2x M3x16mm SHCS (for hinge and trigger) 6x M3 Nuts 6x M3 Washers 1x M3 Threaded Insert Worth it to have 99 extra for other projects. Electronics: A 3.3V Microcontroller with at least 5 pins for data A Battery Charge Circuit for your MCU Adafruit Audio FX Mini Board Adafruit Mono 2.5W Amp Mini Metal Speaker LiPo 1S Battery that will fit 6 or more WS2812B LEDs on Individual Pads Servo wire for those LEDs 2 Small pushbuttons. SPDT Switch Rotary Encoder (aesthetic, optional) Encoder Knob (aesthetic, optional) Tiny extension spring (I found one in an old tapedeck at Goodwill) or small rubber bands. Print SettingsPrinter: ORDbot HadronRafts: Doesn't MatterSupports: YesResolution: 0.4Infill: 20%Notes: This project needs translucent filament! I used clear PETG with good results, but that presented some challenges with overhangs. The "Grip", "Barrel", and small parts don't need to be translucent so choose your favorite filament. Print a mirrored version of "Chamber Stop L". I'm using an E3D V6 Volcano with a 0.6mm nozzle, so the lines are quite thick for mine. The overhangs inside the frame can be a bit tricky, so choose your support settings wisely. I do not need a raft since I use a PEI build plate. I'd like to try to print it in ABS so that I can vapor smooth it, but that will be a challenge.Post-PrintingA. Assemble the Gun BodyI suggest painting the silver paddles on the "power" parts first, painting the red walls next to the paddles, then proceeding to the rest of the build. Those paddles will be a real pain to paint after you have glued everything together. Using a very strong 5 minute epoxy is recommended. After painting the paddles lay all three pieces for each side of the gun (left or right) on wax paper covering a flat surface and epoxy the parts to one another. Try to line up the seams as best as you can and glue. The best method I have found to keep the three pieces aligned is to weigh down each part with something like a can of soda. Repeat for the remaining side. After the epoxy on two halves has had time to set, I suggest trimming any ooze on the mating faces of the two halves so that they will assemble flush. Place a piece of wax paper between the two halves and bolt them together to check that the holes match. Then you can let the epoxy fully cure. Install your magnets. Paint the complete body before installing the small parts since they are usually a silver color, not red. B. Add the Small Parts Paint the parts. Take the two split circles, open them, and force them around the barrel. You can heat them with hot air to make this easier. Glue them to the fin on the barrel to make it look like the in-game model. I had to make these separate because they'd be impossible to print while attached to the barrel. Take the sight and glue some wire in a cross shape to create the reticle. The sight securely to the front of the barrel. It may be a good idea to drill a hole in the barrel so the sight can be inserted into it and glued. Take the three bridge pipes and epoxy them to the assembled gun ONLY ON THE LEFT SIDE to allow the gun to be disassembled later. DO NOT GLUE BOTH POSTS OF THE PIPES. Make sure that they remain aligned while the epoxy cures. This can be done by using hot glue to strap the pipes to the main part while the epoxy sets. Attach the emitter antenna to the front of the barrel. Attach this securely with epoxy or hot glue since it can be quite fragile. Attach the Chamber Stops to the two halves with hot glue. DO NOT INSTALL THE LEFT ONE IF YOU ARE ADDING ELECTRONICS Use a soldering iron with a clean tip to heat the threaded insert and gently press it into the hole where the trigger will be installed. 7, Install the trigger using the 16mm screw and enough washers to reduce friction between the trigger and the body. C. Now Set Up Your ElectronicsI don't have a guide yet, but it would be similar to this one. Here is a wiring diagram. Your pin assignments may vary. The code may not match this specific diagram so examine your pins if there is an issue. PROTOTYPE YOUR SETUP BEFORE YOU INSTALL/SOLDER IT [Try out this code.] STILL DEBUGGING. THANKS FOR YOUR PATIENCE! Install the switches and rotary encoder. Solder your LEDs together and make sure they all fit. Solder your MCU to the LiPo Charger. Solder the Amp the the FX Board. Solder the speaker to the Amp. Hot glue the speaker to the left Chamber Stop print. Solder the switches to the MCU. Install the Chamber Stop with hot glue. Test system over USB. Glue MCU to print with hot glue while still plugged into USB. Secure other electronics with glue. Solder or plug in your LED strip. Install battery. Bolt everything together. Profit.

Design Files

File Size

Power_R.stl
904 KB
Grip_R_Cut.stl
100 KB
Chamber_R.stl
153 KB
Chamber_L.stl
161 KB
Chamber_Stop_R.stl
7.7 KB
Battery.stl
46 KB
Pipe.stl
193 KB
Small_Parts.stl
1.48 MB
Barrel.stl
620 KB
Chamber_Stop_L.stl
7.7 KB
Grip_L_Cut.stl
88 KB
Power_L.stl
944 KB

Comments

Your browser is out-of-date!

Update your browser to view this website correctly. Update my browser now

×